Hewlett Packard 4934A Communications Test Set
Производитель:
Изображение 1 из 1
Если у вас есть другие фотографии или руководства для
Hewlett Packard 4934A, вы можете загрузить файлы в здесь .
Модель:
4934A
Дата:
1988
Категория:
Группа:
Описание:
Transmission Impairment Measuring Set
Информация
The HP 4934A is a wideband (20 Hz to 110 kHz) Transmission
Impairment Measuring Set (TIMS). The transmission impairment
measurements which can be made are listed below.
Level Frequency
Noise
Noise with Tone
Signal to Noise
Impulse Noise
P/AR, (Peak to Average Ratio)
Noise to Ground
The HP 4934A can make measurements directly on leased lines
or on dial-up lines. It has loop holding capability, a
monitor speaker and butt-in connection (useful for talking
to the far end of the test line).
There are four permanently stored frequencies 404 Hz, 1004
Hz, 2804 Hz and 2713 Hz. Any other four frequencies may be
temporarily assigned and stored by the user.
The HP 4934A can test circuits using single frequency (SF)
signaling - use the SF SKIP feature. SF SKIP prevents the HP
4934A from transmitting signaling frequencies in the range
2600 Hz ±150 Hz.
Hасто́льная кни́га тип:
Руководство пользователя
Страницы:
130
Размер:
2.33 Mbytes (2438597 Bytes)
Язык:
english
Пересмотр:
Hасто́льная кни́га ID:
04934-90000
Дата:
1988 09 01
Качество:
Отсканированы документу, все читается.
Дата загрузки:
2017 12 31
MD5:
249483ed4bef84b5ede28aac484bf155
Загрузки:
685
Информация
Operating and Calibration Manual
1. Getting Started
Introduction ... 1-1
Switch-On ... 1-1
Front Panel Features ... 1-2
Demonstrating the HP 4934A, ... 1-5
Demonstration 1 ... 1-5
Demonstration 2 ... 1-6
Error Codes ... 1-7
2. Making Measurements
Preliminary Setup ... 2-1
Connecting the HP 4934A to the Test Circuit ... 2-1
Dial and Hold ... 2-2
Dialing using the HP 4934A and a Butt-in ... 2-3
Receiving an Incoming Call and Holding the Line ... 2-4
Level and Frequency ... 2-6
Principles ... 2-6
Instrument Operation ... 2-8
Message Circuit Noise ... 2-12
Principles ... 2-12
How it is Measured ... 2-14
Instrument Operation ... 2-15
Noise with Tone (Notched Noise) ... 2-16
Principles ... 2-16
How it is Measured ... 2-16
Instrument Operation ... 2-17
Signal to Noise ... 2-18
Principles . ... 2-18
How it is Measured ... 2-18
Instrument Operation ... 2-19
Impulse Noise ... 2-20
Principles ... 2-20
Instrument Operation ... 2-21
P/AR (Peak to Average Ratio) ... 2-24
Principles ... 2-24
How it is Measured ... 2-25
Instrument Operation ... 2-26
Noise to Ground ... 2-27
Principles ... 2-27
How it is Measured ... 2-27
Instrument Operation ... . . . . 2-28
3. General Information
Introduction ... 3-1
Specification ... 3-1.
Safety Considerations ... 3-1
Instruments Covered by Manual ... 3-2
Options Available ... 3-2
Accessories Supplied ... 3-3
Accessories Available ... 3-4
Specification ... 3-4
4. Installation
Introduction ... 4-1
Initial Inspection ... 4-1
Preparation for Use ... 4-2
Power Requirements ... 4-2
Line Fuse ... 4-2
Power Cable ... 4-3
Battery (Option 001 or Retrofit) ... . . . 4-3
Mating Connectors (Front Panel) ... 4-3
Operating Environment ... 4-4
Storage and Shipment ... 4-4
Environment ... 4-4
Packaging ... 4-5
5. Performance Tests
Introduction ... 5-1
Calibration Cycle ... 5-1
Recommended Test Equipment ... 5-2
Operational Verification ... . 5-3
Receiver Frequency ... 5-4
Receiver Level . . . ■ ... . 5-5
Weighting Filters ... 5-6
Impulse Noise Count ... 5-9
Loss of Holding Tone ... 5-10
Hold Circuit ... 5-11
Performance Tests ... 5-17
Transmitter Frequency Accuracy ... 5-18
Transmitter Level Range ... 5-19
Transmitter Level Accuracy ... 5-20
Transmitter Flatness at +10 dBm ... 5-21
Transmitter Flatness at —40 dBm ... 5-22
Transmitter Distortion ... 5-28
Receiver Frequency Range/Accuracy ... 5-31
Receiver Level Accuracy . ... 5-33
Message Circuit Noise Accuracy ... 5-35
Notch Filter Rejection ... 5-37
Signal to Noise Ratio Accuracy ... . 5-39
Impulse Noise Threshold Accuracy ... 5-41
Noise to Ground Accuracy ... 5-43
Peak to Average Ratio (P/AR) Accuracy ... 5-45
A. Service Accessory 1 (SA1) 20 dB Amplifier/4 kHz Filter
Performance Test ... A-l
B. Service Accessory 2 (SA2) Power Splitter/Adder
Performance Test ... B-l