Ramsey Electronics COM 3 Communications Test Set
Производитель:
Изображение 1 из 1
Если у вас есть другие фотографии или руководства для
Ramsey Electronics COM 3, вы можете загрузить файлы в здесь .
Модель:
COM 3
Дата:
1987
Категория:
Группа:
Описание:
Communications Service Monitor
Информация
The COM 3 is a lightweight, compact service monitor for
testing AM and FM transceivers. The internal battery, which
is a standard feature of the COM 3
combined with the
optional carrying case and low weight (13 lbs), make it
ideal for field use. Utilizing specially designed micro
powered oven circuits, warm -up time is minimal, providing
maximum use of the battery.
The frequency range is 100 KHz to 999.999 MHz in 500 Hz
steps. Standard CTS tones as well as a 1 KHz tone can be
generated. RF power is continuosly variable in five ranges
from 0.1 ¡iv to 10,000 ¡j.v. The display is a seven digit
LED type which will display frequencies generated or
received, CTS off air, as well as being an audio and RF
frequency Counter. Deviation and frequency error are
displayed on a 20 segment LED bargraph, which is easily
visible from across the shop.
An internal RF relay switches transmitted power greater than
500 mW to a rear panel mounted BNC connector. This protects
the COM 3 from accidental keying and allows easy connection
of an antenna, power meter, or dummy load.
Hасто́льная кни́га тип:
Руководство пользователя, Схема Cirquit
Страницы:
37
Размер:
9.35 Mbytes (9806215 Bytes)
Язык:
english
Пересмотр:
1.7
Hасто́льная кни́га ID:
Дата:
1987 01 01
Качество:
Отсканированы документу, все читается.
Дата загрузки:
2017 02 04
MD5:
7400a59ce6edc31a90a0b6f39aa4615b
Загрузки:
1069
Информация
Section 1 - General Information
1.1 Introduction
1.2 Specifications
1.3 Options
1.4 Special Modifications
Section 2 - Installation
2.1 Introduction
2.2 Unpacking and Inspection
2.3 Power Requirements
2.4 Enviromental Considerations
Section 3 - Operation
3.1 Introduction
3.2 Front Panel Description
3.3 Initial Turn On
3.4 Generate RF
3.5 RF Output Level
3.6 FM Modulation
3.7 AM Modulation
3.8 CTS Tone Generation
3.9 1 KHz Internal Tone
3.10 External Source Input
3.11 Combining CTS and Internal/External Tone Sources
3.12 Offset+/Offset-
3.13 500 Hz Step
3.14 Storing/Recalling Test Setups
3.15 Spurious Signals
3.16 Leakage
3.17 Audio Count Off Air
3.18 Audio Count External
3.19 RF Count
Section 4 - Typical Test Setups
4.1 Introduction
4.2 Frequency Counter : Off Air
4.3 Frequency Counter : Direct Connection
4.4 Frequency / Deviation Measurements
4.5 20 dB Quieting Measurement
4.6 12 dBSinad Measurement
5.1 General
5.2 512-1018 MHz Coarse Loop PLL
5.3 5-7 MHz Fine Loop PLL -
5.4 1024 MHz Offset PLL
5.5 Output Step Attenuator
5.6 4 MHz Reference Standard
5.7 FM Modulator
5.8 AM Modulator
5.9 1 KHz Source
5.10 Receiver
5.11 16 KHz Reference Generator
5.12 Frequency Error Detector
5.13 Audio Amp
5.14 + 30 Volt and -10 Volt Supplies
5.15 Transmit Protection Circuit
5.16 DC Supply and Battery
5.17 Membrane Switch
5.18 Microprocessor
5.19 Display Drivers
5.20 Audio Frequency Counter
5.21 RF Frequency Counter
5.22 CTS Tone Generation
5.23 Frequency Error/Deviation Display
Section 6 - Documents,Figures
Fig 3.1 Front panel layout Fig 4.1 Block diagram Schematic
diagram Warranty Test data