Informações sobre o equipamento:
|Tektronix 7L13 Analisador de espectro|
|Categoria:||Instrumentos de medição|
|Grupo:||Analisador de espectro|
The 7L13 Spectrum Analyzer is a high-performance communication spectrum Analyzer that plugs into and operates with the 7000-Series mainframe oscilloscopes. It is a swept front end Analyzer that displays absolute amplitude information of signals within the frequency span of 0 Hz to 1.8 GHz. Time domain characteristics, within a 3 MHz bandpass, can also be displayed. Important features of the 7L13 are: 1) Greater than 70 dB dynamic range. 2) Sensitivity down to —128 dBm. 3) Resolution capability from 3 MHz to 30 Hz. 4) Incidental FM’ing less than 10 Hz. 5) Fully calibrated display modes of either 10 dB/Div, 2 dB/Div, or Linear; and a calibrated reference level in dBm. 6) Calibrated sweep spans from 100 MHz/Div to 200 Hz/Div. 7) Digital frequency readout. 8) Full range of video filtering for noise averaging. 9) Baseline clipping to subdue the bright baseline of displays when photographing. 10) Pulse stretching, to enhance pulsed Spectra when using wide frequency spans and resolution bandwidths. 11) Access for a tracking Generator. 12) Frequency and amplitude reference calibrator. If the 7000-Series mainframe features crt readout, the signal parameters and Other pertinent information, such as resolution bandwidth, video filtering, and frequency span, are displayed on the crt readout to simplify the operation of the instrument. Records can then be made of pertinent data by photographing the display. The Analyzer requires three Plug-In widths in the 7000- Series mainframe. ELECTRICAL CHARACTERISTICS The following characteristics and features of the 7L13 Spectrum Analyzer are applicable after a warmup period of 30 minutes or more. CENTER FREQUENCY Range: 1 kHz to 1.8 GHz. Resolution of the Center Frequency Indicator: Within 1 MHz. Accuracy: ±(5 MHz + 20% of the Freq Span/Div). The center frequency is indicated by LED readout on the 7L13 and crt readout when the 7000-Series mainframe has this feature. FREQUENCY SPAN Calibrated spans from 200 Hz/Div to 100 MHz/Div in a 1-2-5 sequence, plusO Hz and MAX SPAN positions. In the 0 Hz position, the Analyzer is a fixed tuned receiver for time domain analysis. In the MAX SPAN position the frequency span is approximately 1.8 GHz. Accuracy: Within 5% of the indicated frequency separation. Linearity over the center 8 divisions is within 5%. RESOLUTION Six resolution bandwidth selections from 30 Hz to 3 MHz, in decade steps, are provided. Resolution bandwidth may be coupled or uncoupled from the frequency span selector. Bandwidth accuracy: Resolution bandwidth, at the 6 dB down point, is within 20% of the resolution selected. Shape factor (60:6 dB ratio): 12:1 or better for 30 Hz resolution and 4:1 or better with resolution of 300 Hz or more except 3 MHz. Maximum bandwidth 60 dB down with 3 MHz resolution, is 13 MHz. Signal level change over the six resolution bandwidth selections is less than 0.5 dB. STABLITY (after a 2 hour warmup period) Within 2 kHz per hour at a fixed temperature, when x phase locked: within 50 kHz when not phase locked. INCIDENTAL FM (see Fig. 3-5) 10 Hz (peak-to-peak) or less when phase locked, and 10 kHz (peak-to-peak) or less for 5 seconds when out of phase locked mode. VIDEO FILTERING Three selections of video filtering; 10 Hz, 300 Hz and 30 kHz are provided for signal or noise averaging. DISPLAY LOG 10 dB/DIV: Provides a calibrated 70 dB dynamic range with an accuracy that is within 0.1 dB/1 dB to a maximum of 1.5 dB over the full dynamic range. LOG 2 dB/DIV: Provides a calibrated 14 dB dynamic range with an accuracy that is within ±0.4 dB/2 dB to a maximum of 1.0 dB over the 14 dB dynamic range. LIN: Provides a linear display from approximately 0.7/iV (100 dBm) full scale, to 7.07 volts (+30 dBm). Amplitude linearity is within 10% over the graticule height. REFERENCE LEVEL Reference level operation is in calibrated 10 dB steps from -110 dBm to +30 dBm, within ±2 dB. (Accuracy includes the attenuator and gain switching effects when the two are not offsetting each Other.) Reference level operation below 100 kHz becomes limited to a range from +30 dBm to-50 dBm as the center frequency approaches 1 kHz. Reference level deviation, between display modes, is less than 2 dB from 2 dB/DIV to 10 dB/DIV and less than 0.5 divisions from 2 dB/DIV to LIN. This deviation is a function of the Oscilloscope vertical linearity. An UNCAL indicator signifies when the display is not calibrated. DISPLAY FLATNESS +1 dB, —2 dB with respect to the level at 50 MHz, over any selected frequency span.
Estes manuais estão disponíveis para os equipamentos acima:
|Tektronix -- 7L13 -- Serviço e Manual do Usuário|
|Tipo manual:||Serviço e Manual do Usuário|
|Tamanho:||54.20 Mbytes (56832819 Bytes)|
|Data:||01 Abril 1974|
|Qualidade:||Documento Scaned, a leitura parcialmente mal, não parcialmente legível.|
|Envie data:||15 Janeiro 2017|
|Downloads:||106 desde 15 Janeiro 2017|
on ANSI Y 1.1,1972Standards.This manual isdivided into ten major sections that provide the following information: Section 1 — General Information and Specifications: Contains the instrument description and specifications. Section 2 — Operation Instructions: Information relative to installing and operating the instrument. Section 3 — Performance Check: Provides procedures to check the operational performance of the instrument plus additional performance check procedures that require test equipment to verify that instrument performance is in accordance to specifications. Section 4 — Calibration Procedure: Describes test equipment setup and adjustment procedures required to calibrate the instrument. Section 5 — Circuit Description: Provides basic and general circuit analysis that may be useful when servicing or operating the instrument. Section 6 — Maintenance Instructions: Describes routine and corrective maintenance procedures with detailed instructions for replacing assemblies, subassemblies, and individual components. Troubleshooting procedures, plus general information that may aid in servicing the instrument, are also provided. An exploded drawing is part of Section 10. Section 7 — Options: Describes options available for the instrument. Section 8 — Electrical Parts List: Provides information necessary to order replaceable parts and assemblies. Section 9 — Diagrams: Provides functional block diagram and detailed circuit schematics. Located adjacent to the diagram (usually on the back of the preceding diagram) are pictoral layout drawings that show sub- assembly and component locations. IC logic diagrams, waveforms and voltage data, fortroubleshooting orcircuit analysis, are also provided adjacent to or on the diagram. Section 10 — Mechanical Parts List, Exploded Drawings and Accessories: Provides information necessary to order replaceable parts. The Parts List is cross-referenced to the Electrical Parts List. Exploded drawing shows sequence of assembly and identifies assemblies. Changes and Corrections: Provides updating information for the manual in the form of inserts. These inserts are incorporated into the manual text and diagrams when the manual is reprinted.
No comments yet. Be the first!