Tektronix SG 5030 Generator
Producent:
Model:
SG 5030
Data:
1990
Kategoria:
Grupa:
Opis:
Programmable Leveled Sine Wave Generator

Informacja

The SG 5030 Programmable Leveled Sine Wave Generator is a GPIB programmable TM 5000-series Plug-In instrument designed to provide a low-distortion sinusoidal waveform with leveled output amplitude. Frequency, amplitude, and the front-panel store/recall parameters are fully programmable. Parameter values are displayed by 8 seven-segment LEDs in the display window. The SG 5030 output amplitude is programmable from 4.5mV to 5.5V peak-to-peak into 50Q, and has a frequency range of 0.1 Hz to 550MHz with a reference frequency of 50kHz. Additional connectors provide timebase input and output reference signals to external sources.

pokaż więcej

Serwis i User Manual
Typ ręczny:
Serwis i User Manual
Strony:
223
Rozmiar:
17.66 Mbytes (18521479 Bytes)
Język:
english
Rewizja:
Revised
Ręczny ID:
070-7703-01
Data:
Jakość:
Skanowany dokument, wszystko czytelne.
Data przesłania:
28 kwiecień 2013
MD5:
747805af4504b9ce57562e4b96b7d2e1
Pobrane:
1269

Informacja

Table of Contents Operator Safety Summary . . . ... vii Service Safety Summary ... viii Section 1 Specifications ... 1-1 Introduction ... 1-1 Instrument Description ... 1-1 Electrical Characteristics ... 1-2 Section 2 Operating instructions ... 2-1 Preparation For Use ... 2-1 Front Panel Controls, Connectors and Display ... 2-2 Operator Familiarization ... 2-6 Power-Up Sequence ... 2-6 Function and Parameter Selection ... 2-6 Making Bandpass Measurements ... 2-10 Section 3 Programming ... 3-1 Introduction ... 3-1 IEEE-488 Interface Function Subsets ... 3-1 Commands ... 3-2 Command Summary ... 3-3 Messages and Communication Protocol ... 3-16 Message Protocol ... 3-17 Instrument Responses to IEEE-488 Interface Messages ... 3-18 Remote-Local Operation ... 3-18 Status And Error Reporting ... 3-19 Error Messages Sent To The Front Panel ... 3-20 Bus Error/Event Codes And Serial Poll Response ... 3-21 Power-on Sequences And Settings ... 3-21 Programming Examples ... 3-24 WARNING I The remaining portion of this Table of Contents liste information that may expose personnel to hazardous voltages. The information listed in the remaining sections of this manual is for qualified personnel only. Section 4 Theory of Operation ... 4-1 Introduction ... 4-1 SG 5030 Overview ... 4-1 Block Diagram Description ... 4-2 Circuit Theory Notes ... 4-3 Detailed Circuit Description ... 4-4 Section 5 Performance Check ... 5-1 Introduction ... 5-1 Test Equipment Required ... 5-1 Preparation ... 5-4 1. Check Frequency Accuracy ... 5-4 2. Check Spectral Purity ... 5-6 3. Check Amplitude Accuracy ... 5-9 4. Check Amplitude Flatness ... 5-11 5. Check Output VSWR ... 5-17 Section 6 Adjustment Procedure ... 6-1 Introduction ... 6-1 1. Preparation ... 6-1 2. Adjust Output Hybrid Bias ... 6-2 3. Adjust Internal Timebase Frequency ... 6-4 4. Set Offset and Gain Cal Constants ... 6-5 Section 7 Maintenance ... 7-1 Introduction ... 7-1 General Maintenance ... 7-1 Loss of NVRAM ... 7-1 Troubleshooting Aids ... 7-1 Output Hybrid Bias Setup ... 7-5 Cleaning ... 7-5 Obtaining Replacement Parts ... 7-7 Diagnostics ... 7-8 1. Self Tests ... 7-9 2. Operational Errors ... 7-11 Removal Instructions ... 7-12 Cabinet Side, Top, and Rear Panel Removal ... 7-12 Circuit Board Removal ... 7-12 Section 8 Options ... 8-1 Section 9 Replaceable Parts Lists ... 9-1 Parts Ordering Information ... 9-1 Parts List Entry Description ... 9-1 Cross Index - Mfr. Code Number to Manufacturer ... 9-2 Replaceable Electrical Parts ... 9-5 Replaceable Mechanical Parts ... 9-33 Accessories ... 9-35 Standard Accessories ... 9-35 Optional Accessories ... 9-35 Section 10 DIAGRAMS AND CIRCUIT BOARD ILLUSTRATIONS ... 10-1

pokaż więcej

Instrukcja obsługi
Typ ręczny:
Instrukcja obsługi
Strony:
98
Rozmiar:
11.07 Mbytes (11608603 Bytes)
Język:
english
Rewizja:
Revised
Ręczny ID:
070-7705-01
Data:
Jakość:
Skanowany dokument, wszystko czytelne.
Data przesłania:
27 kwiecień 2013
MD5:
ef371cb709455ec02237b53c1d54de76
Pobrane:
1422

Informacja

Table of Contents Operator Safety Summary ... v Section 1 Specifications ... 1-1 Introduction ... 1-1 Instrument Description ... ... 1-1 Electrical Characteristics ... 1-2 Section 2 Operating Instructions ... 2-1 Preparation For Use ... 2-1 Front Panel Controls, Connectors And Display ... 2-2 Operators Familiarization ... 2-6 Power-Up Sequence ... 2-6 Function and Parameter Selection ... 2-6 Making Bandpass Measurements ... 2-10

pokaż więcej

Komentarze

Brak komentarzy, bądź pierwszy!

Dodaj Komentarz

* Wymagane
1000
Captcha