LeCroy 9400 Oscyloskop
Manufacturer:
No picture available!
Maybe you can upload a pic for the
LeCroy 9400 ?
If you have any other manuals for the
LeCroy 9400 you can upload the files here .
Model:
9400
Date:
1986
Category:
Group:
Description:
DUAL 125 MHz DIGITAL OSCILLOSCOPE
Information
DUAL 125MHz DIGITAL Oscilloscope
The LeCroy 9400 Dual Digital Oscilloscope is a powerful general purpose tool for waveform measurements. Designed to operate as easily as your familiar analog Oscilloscope, the 9400 brings you a whole new range of capabilities to measure and characterize your waveforms with greater precision and confidence.
With the 9400 you gain :
HIGHER PRECISION
Two independent 125 MHz channels, each with a high performance 8-bit ADC, convert your input signals with better than 1% accuracy. Each input is sampled at a maximum rate of 5 Gigasample/sec for repetitive waveforms and 100 Megasample/sec for single events. The high sampling rate combined with extremely long 32,000 data point acquisition memories, permit time measurements with an accuracy of 0.002%. The 9400’s easy to use Voltage, Time and Crosshair Cursors assist you in making precise measurements.
HIGH RESOLUTION DISPLAY
The large, high resolution display produces bright, stable, razor Sharp pictures of your signal under any rate conditions. Up to 4 waveforms can be displayed simultaneously. The high resolution (1024 x 1024 pixels) display permits very accurate comparisons and waveform measurements. With "x100” timescale expansion, you zoom in on details for analysis and exact cursor placement.
SINGLE TRANSIENT RECORDING
The 9400 is an extremely powerful transient recorder with a maximum sampling rate of 100 Megasample/sec. Rare events cannot be missed. The long 32,000 data point acquisition memories, combined with the continuously adjustable trigger (from 100% pre-trigger to 10,000 x time/div post-trigger), give unparalleled flexibility. Both channels are sampled simultaneously and exact time correlation between channels is maintained.
FULL PROGRAMMABILITY
All the 9400’s front panel knobs and push-buttons are fully programmable. RS232C and GPIB interfaces facilitate computer aided testing, remote-control operation and ATE applications. Up to 7 different front-panel setups can be stored and easily recalled to simplify successive test operations. A single pushbutton initiates a Screen Dump for accurate hard copies of the display via a wide range of digital plotters.
SIGNAL PROCESSING CAPABILITY
Elaborate signal processing can be performed on the digitally stored waveform. For specific application analysis, the captured waveform can be transferred to a computer and studied with your own Software. Processed data can then be transferred back to the 9400 for reference. For front end data reduction and processing, LeCroy offers optional firmware packages including signal averaging, arithmetic array operations and Fast Fourier Transforms.
Manual type:
Instrukcja obsługi
Pages:
158
Size:
6.58 Mbytes (6903361 Bytes)
Language:
english
Revision:
Manual-ID:
Date:
1986 12 01
Quality:
Skanowany dokument, wszystko czytelne.
Upload date:
2021 01 11
MD5:
174e8567335bb7d17ade592719c385cf
Downloads:
298
Manual type:
Instrukcja serwisowa
Pages:
432
Size:
13.66 Mbytes (14320484 Bytes)
Language:
english
Revision:
Manual-ID:
Date:
Quality:
Skanowany dokument, wszystko czytelne.
Upload date:
2013 01 26
MD5:
91b152e18a223df05746a8e7c16e76c4
Downloads:
2074
Information
The present Service Manual applies to both the 9400 and
the 9400À DSOs. Both models are called 9400 when the
information applies equally to both oscilloscopes.
Where the two models have distinct features, the model
number 9400 or 9400A is explicitly stated.
The chief purpose of this manual is to provide information
for technicians, mainly authorized LeCroy repair office
personnel, who are responsible for repairs and modifications
to the LeCroy 9400.9400A DSOs.
To this end, the descriptions provided are intended to be
of sufficient depth to enable faults to be diagnosed to
the level of the relevant board, so that the customer can
be quickly supported by exchange of boards. In many cases
the fault may be corrected at the local LeCroy office,
but there are several areas of the circuitry where
replacement of a part would need to be followed by
calibration which could be done only with specialized
equipment available at the main LeCroy establishments.
Calibration procedures are given in this manual only
for those areas which could be serviced locally.
A DSO repair intervention at board exchange level
can only be done by qualified technicians who have
followed the basic 9400.9400A service training.
LeCroy also offers these courses to customers. In
addition, there is a very comprehensive 9400 Adjustment
and Calibration Software Package CALS0FT (order codes
CS01/CS02) based on the IBM PC or a compatible computer.
This Software package is also available to customers,
as well as all the hardware making up the 9400 Automated
Calibration System (order code CS-S) which is used
in all LeCroy service offices to ensure full performance
of the instrument. This system provides Calibration
Certificates traceable to NBS. LeCroy also offers training
classes on DSO calibration.
This manual could be improved by the inclusion of useful
information resulting from detection and correction
of faults in 9400.9400A DSOs at any LeCroy office.
Each time a DSO is opened, an official LeCroy repair
report should be sent to LeCroy S.A., attention
Customer Service. The information is entered into
a centrally maintained DSO data base for failure
analysis and engineering feedback.
Before undertaking any work on the 9400 DSO you should
read the next sections - WARNINGS and VALID RANGE
of FIELD MAINTENANCE.
