Electronic Navigation Industries A-300 Wzmacniacz
Producent:
Zdjęcie 1 z 1
Jeśli masz inne zdjęcia lub instrukcje obsługi dla
Electronic Navigation Industries A-300, możesz przesłać pliki tutaj .
Model:
A-300
Data:
0
Kategoria:
Grupa:
Opis:
BROADBAND POWER AMPLIFIER
Informacja
The ENI Model A300 is an all solid state Amplifier which has
a flat frequency response from .3 MHz to 35 MHz. It provides
300 watts of linear power with low harmonic and
intermodulation distortion. Gain is 55 dB nominal, with a
variation of less than ± 1.0 dB over the entire frequency
range. Input and output impedance are 50 ohms and the unit
may be driven to full power output by most RF synthesizers,
signal generators and swept signal sources.
The ENI Model A300 will deliver its rated power output into
any load impedance, regardless of match. Built-in protection
circuitry will absorb the power reflected from a mismatched
load without causing failure or oscillation.
Output RF voltage is displayed on the front panel meter. The
Model A300 is packaged for bench mounting and is shipped
with rack mounting adapters. Its integral power
supply and cooling operate from a 115 or 230 V ac 50/60 Hz
main supply.
The Model A300 will raise the power level of signal sources
and generators without requiring tuning or band- switching.
The Class A linear circuitry will amplify signals of AM, FM,
SSB, TV and complex modulations limited only by their peak
input and bandwidth, with minimum distortion.
Typ ręczny:
Serwis i User Manual
Strony:
31
Rozmiar:
1.60 Mbytes (1673279 Bytes)
Język:
english
Rewizja:
Ręczny ID:
Data:
Jakość:
Skanowany dokument, czytając częściowo źle, nie częściowo czytelny.
Data przesłania:
2016 01 25
MD5:
8831ab8fd7b5899ced065e1324208e5a
Pobrane:
593
Informacja
CHAPTER 1 GENERAL INFORMATION 1-1
1.1 introduction ... 1-1
1.2 Specifications ... 1-1
1.3 instrument Identification ... 1-1
CHAPTER 2 PREPARATION 2-1
2.1 Initial Inspection ... 2-1
2.1.1 Mechanical Check ... 2-1
2.1.2 Claim for Damage ... 2-1
2.1.3 Performance Check ... 2-1
2.2 Preparation for Use ... 2-1
2.2.1 Power Requirements ... . 2-1
2.2.2 Power Cable Ground Protection . 2-1
2.2.3 Cooling ... 2-2
2.3 Rack Mounting ... 2-2
2.4 Packaging for Reshipment ... 2-2
CHAPTER 3 OPERATION 3-1
3.1 Functional Description ... 3-1
3.2 Controls, Indicators and
Connectors ... 3-1
3.3 Operating Procedure ... 3-1
3.4 Precautions ... 3-1
CHAPTER 4 PRINCIPLES OF OPERATION 4-1
4.1 General ... 4-1
4.2 Block Diagram Description ... 4-1
4.2.1 Driver Amplifier Module {A48A}
A300-4382 ... 4-1
4.2.2 Power Amplifier Module (A40A)
A300-4381 ... 4-1
4.2.3 Bias Regulator Module (A49)
A300*4387 ... 4-3
4.2.6 RF Voltmeter Module
(A29M) A300-4386 ... 4-3
4.2.7 Power Distribution
A300-2381 ... 4-3
CHAPTER 5 PERFORMANCE
TEST PROCEDURES 5-1
5.1 Performance Tests . ... 5-1
5.1.1 General ... 5-1
5.1.2 Test Equipment Required ... 5-1
5.1.3 Gain and Gain Variation Test.. . 5-1
5.1.3.1 Calibration of Set Up ... 5-1
Paragraph Page
5.1.3.2 Measurement Procedure ... 5-1
5.1.4 RF Output Power Test ... 5-2
5.1.4.1 Measurement Procedure ... 5-2
5.1.5 RF Output Distortion Test ... 5-2
5.1.5.1 Measurement Procedure ... 5-2
CHAPTER 6 TROUBLESHOOTING AND REPAIR 6-1
6.1 Troubleshooting ... 6-1
6.2 Locating Faulty RF Module ... 6-2
6.2.1 General ... . 6-2
6.2.2.1 Two-Way Output Combiner
Test {A51> A300-4383 ... 6-3
6.2.2.2 Heatsink Assembly Test
A300-3385 ... 6-3
6.2.2.2.1 Bias Voltage Check ... 6-3
6.2.2.2.2 RF Power Test ... 6-3
6.2.2.3 Driver Amplifier Module
(A48A) A300-4382 ... 6-4
6.2.3 RF Voltmeter
(A29M) A300-4386 ... 6-4
6.2.3.1 Alignment Procedure ... 6-4
6.3 DC Power Supply ... 6-4
6.3.1 General . . ... 6-4
6.3.2 Test Procedure ... 6-5
6.4 Disassembly Procedure ... 6-5
6.4.1 General ... 6-5
6.4.2 Tools Required ... 6-5
6.4.3 Removal of Cover ... 6-5
6.4.4 Driver Amplifier Heatsink
Assembly A300-3386 ... 6-5
6.4.6 Power Amplifier Heatsink
Assembly A300-3385 ... 6-5
6.4.7 Power Amplifier Power Supply
A300-3387 ... 6-6
6.4.8 Driver Amplifier Power Supply
A300-3388 ... 6-6
6.4.10 Power Amplifier Module
(A40A) A300-4381 ... 6-6
6.4.11 Two-Way Output Combiner
(A51) A300-4383 ... 6-6
CHAPTER 7 SCHEMATICS AND PARTS LIST 7-1
7.1 Schematic Diagrams ... 7-1
7.2 Parts List ... 7-1
7.3 List of Manufacturers ... 7-1