BK Precision 2165A Spectrum analyzer
Producent:
Model:
2165A
Data:
Kategoria:
Grupa:
Opis:
Informacja
The spectrum Analyzer permits the detection of spectrum components of electrical signals in the frequency range of 0.15 to 1050 MHz for Models 2625 and 2630 and 0.15 to 500 MHz for Models 2615 and 2620. The detected signal and its content have to be repetitive. In contrast to an Oscilloscope operated in Yt mode, where the amplitude is displayed on the time domain, the spectrum Analyzer displays amplitude on the frequency domain (Yf). The individual spectrum components of “a signal” become visible on a spectrum Analyzer. The Oscilloscope would display the same signal as one resulting waveform. Models 2625 and 2630 The spectrum Analyzer works according to the triple superhet receiver principle. The signal to be measured (fin = 0.15 MHz to 1050 MHz) is applied to the 1st mixer where it is mixed with the signal of a variable voltage controlled Oscillator (fLO 1350 MHz - 2350 MHz). This Oscillator is called the lst LO (local oscillator). The difference between the Oscillator and the input frequency (fLO - fin = 1st IF) is the first intermediate frequency, which passes through a waveband filter tuned to a center frequency of 1350 MHz. It then enters an Amplifier, and this is followed by two additional mixing stages, oscillators and amplifiers. The second IF is 29.875 MHz and the third is 2.75 MHz. In the third IF stage, the signal can be selectively transferred through a filter with 400 kHz or 20 kHz bandwidth before arriving at an AM demodulator. The logarithmic output (video signal) is transferred directly, or via a low pass filter to another Amplifier. This Amplifier output is connected to the Y deflection plates of the CRT. Models 2615A and 2620A The spectrum Analyzer works according to the triple superhet receiver principle. The signal to be measured (fin = 0.5 MHz to 500 MHz) is applied to the 1st mixer where it is mixed with the signal of a variable voltage controlled Oscillator (fLO 610 MHz - 1110 MHz). This Oscillator is called the 1st LO (local oscillator). The difference between the Oscillator and the input frequency (fLO - fin = 1st IF) is the first intermediate frequency, which passes through a waveband filter tuned to a center frequency of 609.5 MHz. It then enters an Amplifier, and this is followed by two additional mixing stages, oscillators and amplifiers. The second IF is 29.5 MHz and the third is 2.9 MHz. In the third IF stage, the signal can be selectively transferred through a filter with 250 kHz or 20 kHz bandwidth before arriving at an AM demodulator. The logarithmic output (video signal) is transferred directly, or via a low pass filter to another amplifier. This Amplifier output is connected to the Y deflection plates of the CRT. The X deflection is performed with a ramp Generator voltage. This voltage can also be superimposed on a dc voltage which allows for the control of 1st LO. The spectrum Analyzer scans a frequency range depending on the ramp height. This span is determined by the scan width setting. In ZERO SCAN mode only the direct voltage controls the 1st LO. Models 2620A and 2630 each include a tracking Generator. This Generator provides sine wave voltages within the frequency range of 0.1 to 1050 MHz for Model 2630 and 0.1 to 500 MHz for Model 2620A, The tracking Generator frequency is determined by the first Oscillator (1st LO) of the spectrum Analyzer section. Spectrum Analyzer and tracking Generator are frequency synchronized.

pokaż więcej

Instrukcja obsługi
Typ ręczny:
Instrukcja obsługi
Strony
28
Rozmiar:
1.14 Mbytes (1193155 Bytes)
Język:
english
Rewizja:
Ręczny ID:
480-780-9-001
Data:
Jakość:
Skanowany dokument, wszystko czytelne.
Data przesłania:
24 styczeń 2017
MD5:
ef52e1ff08e3b886d2f8659c627e2d12
Pobrane:
568
Informacja
TEST INSTRUMENT SAFETY ... Inside front cover SPECIFICATIONS ... 5 OPTIONAL Accessories ... 6 GENERAL INFORMATION ... 7 Symbols ... 7 Tilt handle ... 7 Safety ... 7 Operating Conditions ... 8 Maintenance ... 8 Selecting the Line Voltage ... 8 INTRODUCTION ... 9 General ... 9 Operating Considerations ... 9 CONTROLS AND INDICATORS ... 10 CALIBRATION ... 15 Vertical Calibration ... 15 Horizontal Calibration ... 15 Page INTRODUCTION TO SPECTRUM ANALYSIS ... 17 General ... 17 Types of Spectrum Analyzers ... 17 Spectrum Analyzer Requirements ... 18 Frequency Measurements ... 18 Resolution ... 18 Sensitivity ... 19 Video Filtering ... 19 Spectrum Analyzer Sensitivity ... 19 Frequency Response ... 20 Tracking Generators ... 20 APPENDIX-dBm CONVERSION ... 22 CUSTOMER SUPPORT ... 23 INSTRUMENT REPAIR SERVICE ... 23 WARRANTY SERVICE INSTRUCTIONS ... 24 LIMITED ONE-YEAR WARRANTY ... 25

pokaż więcej

Komentarze (0)

Brak komentarzy, bądź pierwszy!

Dodaj Komentarz

* Wymagane
1000
Captcha