Keithley 7999-6 Interfejs
Producent:
Brak zdjęcia!
Może możesz przesłać zdjęcie za
Keithley 7999-6 ?
Jeśli masz jakieś inne podręczniki dla
Keithley 7999-6, możesz przesłać pliki tutaj .
Model:
7999-6
Data:
2001
Kategoria:
Grupa:
Opis:
GPIB RF Relay Unit
Informacja
The Model 7999-6 is an IEEE-488 controlled, single or dual, 4 or 6 pole, 19-inch rack
mounted relay unit. Additional features of the Model 7999-6 are as follows:
• N-type bulkhead connectors (insulated)
• +24VDC power connections
• LED indicators for error, power, and relay status
• Operating range to 4GHz (relay dependent)
• Can be upgraded from 4-pole to 6-pole relays
Typ ręczny:
Serwis i User Manual
Strony:
87
Rozmiar:
1.40 Mbytes (1465105 Bytes)
Język:
english
Rewizja:
A
Ręczny ID:
7999-6-901-01
Data:
Jakość:
Dokument elektroniczny, bez skanowania, bardzo dobrze czytelne.
Data przesłania:
2014 03 02
MD5:
eda9430778a16daf86eaac26278b6410
Pobrane:
601
Informacja
1 General Information
Introduction
...
1-2
Feature overview
...
1-2
Warranty information
...
1-2
Manual addenda
...
1-2
Safety symbols and terms
... 1-3
Specifications
...
1-3
Unpacking and inspection
... 1-3
Inspection for damage
... 1-3
Handling precautions
... 1-3
Shipment contents
...
1-4
Instruction manual
...
1-4
Repacking for shipment
... 1-4
Connections
...
1-4
2 Connections
Introduction
...
2-2
Handling precautions
...
2-2
Configuration
...
2-2
Layout
...
2-2
Simplified schematic
... 2-4
Connections
...
2-5
GPIB control connection
... 2-5
Power connector
...
2-8
3 Operation
Introduction
...
3-2
Maximum signal considerations
... 3-2
Bus operation (GPIB)
...
3-3
Bus connections
...
3-3
Primary address
...
3-3
Programming syntax
... 3-3
Response messages
... 3-7
Status model
...
3-8
Event register sets
... 3-10
Enable registers
...
3-11
Queues
...
3-11
Status byte and SRQ
... 3-13
Service request enable register
... 3-14
Serial polling and SRQ
... 3-15
Clearing registers and queues
... 3-16
Programming enable registers
... 3-17
Reading registers
...
3-17
Common commands
...
3-18
GPIB commands
...
3-26
ROUTe commands
...
3-26
:CLOSe ...
3-28
:CONFigure ...
3-29
STATus commands
...
3-30
:QUEue ...
3-30
SYSTem commands
... 3-32
Manual operation
...
3-34
Switching considerations
... 3-35
Connector integrity
...
3-35
Voltage Standing Wave Ratio
... 3-35
Path isolation
...
3-36
Insertion loss
...
3-36
RFI/EMI
...
3-36
Errors
...
3-37
4 Service Information
Introduction
...
4-2
Handling and cleaning precautions
... 4-2
Handling precautions
... 4-2
Card and connector cleaning
... 4-2
Performance verification
... 4-3
Environmental conditions
... 4-3
Recommended equipment
... 4-3
Channel resistance tests
... 4-3
Replacing components
...
4-4
Replacement parts
...
4-4
Replacement precautions
... 4-5
Soldering considerations
... 4-5
Relay replacement
...
4-5
Circuit board removal
... 4-8
GPIB address
...
4-8
5 Replaceable Parts
Introduction
...
5-2
Parts list
...
5-2
Ordering information
...
5-2
Factory service
...
5-2
Component layout
...
5-2