Skanti P5013 Ontvanger
Fabrikant:
Afbeelding 1 van 1
Als je nog andere foto's of handleidingen hebt voor de
Skanti P5013 kun je de bestanden hier uploaden .
Model:
P5013
Datum:
0
Categorie:
Groep:
Omschrijving:
Power Unit
Informatie
The R5001 marine and general purpose Receiver is designed
for use in a marine main radio station. The Receiver has
synthesized operation in the frequency range 10 kHz to
29,999.9 kHz.
The Receiver is designed for reception of type F1, A1, A2,
A2H, A3, A3H and upper-si-deband A3A and A3J signals. It is
fully transistorized, and widespread use is made of
integrated circuits. These features, in connection with
thefactthat no crystal ovens are used, cause the Receiver to
be ready for operation immediately after having been swiched on.
Depending on the power pack installed in it, the Receiver
can be powered from a 24 V battery or from AC voltages
normally occurring in practice.
The dimensions match a 19-inch standard rack.
Because we are constantly processing the experience gained
during the produc-tionand operation of ourequipment, it is
possible for minor modifications to occur relative to the
information given in this instruction manual. Wherever
practicable, however, any corrections will be listed on a
correction sheet at the back of the front cover of this manual.
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
151
Grootte:
5.74 Mbytes (6017642 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
Datum:
Kwaliteit:
Gescand document alle leesbaar.
Upload datum:
2014 01 12
MD5:
84d19cc831af7577995a72a0cfe93cd9
Downloads:
2739
Informatie
1. INTRODUCTION 1- 1
2. OPERATING INSTRUCTIONS 2- 1
2.1. Tuning to 500 kHz and 2182 kHz 2-
2.2. Tuning to an A1, F1 or SSB Station in the Preselector
Range 2-
2.3. Tuning to an F1 or SSB Station in the Duplex Ranges 2-
2.4. Tuning to an AM Station 2-
2.5. Operating Controls and Their Functions 2-
INSTALLATION 3-
3.1. Mounting the Cabinet 3-
3.2. Disassembling the Receiver 3-
3.3. Connection to the Permanent Installation 3-
3.4. Earth Connection 3-
3.5. Antenna 3-
3.6. Exchanging the Input Impedance 3-
3.7. Remote Speaker 3-
3.8. Muting 3-
3.9. Replacement of Power Packs 3-
4. TECHNICAL DATA 4- 1
5. TECHNICAL DESCRIPTION 5- 1
5.1. Mechanical 5- 1
5.2. Circuit Description, General 5- 1
5.3. Circuit Summary, Signal Path 5- 1
5.4. Circuit Description, Signal Path Boards 5- 2
5.5. Circuit Summary, Frequency Synthesizer 5- 4
5.6. Circuit Description, Frequency Synthesizer 5- 5
5.7. Circuit Summary, Frequency Selection 5- 7
5.8. Circuit Description, Frequency Selection 5- 8
5.9. Circuit Summary, P 5010, 24V DC Power Pack 5-10
5.10. Circuit Description, P 5010, 24V DC Power Pack 5-10
5.11. Circuit Summary, P 5011, AC Power Pack 5-11
5.12. Circuit Description, P 5011, AC Power Pack 5-11
5.13. Circuit Summary, P 5012, 24 V DC/AC Power Pack 5-11
5.14. Cicuit Description, P5012
24V DC/AC Power Pack 5-12
6. SIMPLE SERVICE 6- 1
6.1. Incorrect Operation 6- 1
6.2. Battery 6- 1
6.3. Replacement of Fuses 6- 1
7. REPAIR AND ALIGNMENT 7- 1
7.1. Introduction 7- 1
7.2. Cross Slot Screws 7- 1
7.3. Locating Subunits and Components 7- 1
7.4. Locating Faults 7- 1
7.5. Test Points 7- 1
7.6. AC Voltages 7- 1
7.7. DC Voltages 7- 2
7.8. Typical Sensitivity Levels 7- 2
7.9. Adjustments 7- 2
7.10. Realignment of Input Filters /202 or /216 7- 3
7.11. /203 Realignment of 2nd Mixer and Clarifier
Oscillator 7- 6
7.12. /205 Realignment of IF Amplifier Detector and AGC 7- 6
7.13. /220 Realignment of AF Amplifier 7- 7
7.14. /220 Frequency Adjustment of the TCXO 7- 7
7.15. /209 Realignment of VCOi and VCO2 7- 7
7.16. /208 Realignment of Loop Translator 7- 8
7.17. /210 Realignment of VCOs 7-9
8. PARTS LISTS AND CIRCUIT DIAGRAMS 8- 1
8.1. Numbering 8- 1
8.2. Switches 8- 1
8.3. Terminals 8- 1
8.4. Voltages 8- 1
8.5. Test Points 8- 1
8.6. Symbol Explanation 8- 1
8.7. Abbreviations 8- 4
8.8. Parts List 8- 5
8.9. Diagrams 8-50