Xantrex XDL 56-4P Voeding
Fabrikant:
Geen foto beschikbaar!
Misschien kan je een foto uploaden voor de
Xantrex XDL 56-4P ?
Als je nog andere handleidingen hebt voor de
Xantrex XDL 56-4P kun je hier de bestanden uploaden .
Model:
XDL 56-4P
Datum:
2008
Categorie:
Groep:
Omschrijving:
Informatie
Unmatched Precision, Unrivalled Performance
The XDL series represents the ‘next generation’ of laboratory power supplies offering an
unparalleled level of precision.
Voltage and current are controlled using 16 bit DACs enabling voltages to be set to 1mV
resolution even at full output. Indeed, the accuracy is sufficient for the PSU to be used as a
calibration source for most hand-held DMMs.
The XDL series uses pure linear technology and offers unrivalled performance in terms of
regulation, output noise and dynamics. Line and load regulation are at the limit of measurement
(nominally 0·002%). Output noise is less than 500μV rms. Recovery time from transient current
pulses is better than 50μs.
The XDL series provides full remote sense capability via dedicated sense terminals. Remote
sense is essential to maintain precise regulation at the load (two 0·03Ω connection leads will drop
300mV at 5 Amps). When remote sense is not required, internal local sensing can be selected at
the touch of a button.
Multiple Ranges for Greater Flexibility
The XDL series provides multiple ranges for increased current capability at lower voltages. The
main range offers 0 to 35 Volts at up to 3 Amps (XDL 35-5) or 0-56V at up to 2 Amps (XDL 56-4).
The higher current range provides up to 5 Amps for voltages up to 15V (XDL 35-5) or 4 Amps for
voltages up to 25V (XDL 56-4). A further low current range provides enhanced current setting and
measurement resolution of 0·1mA.
The product of voltage and current can be displayed at any time by pressing the VxA button. The
power is displayed to a resolution of 0·01 Watts.
Fast, Simple and Safe to use
The user Interface of the XDL series has been carefully designed to provide rapid control whilst
guarding against any possibility of error.
Voltage and current setting can be performed either by direct numeric entry or, for applications
where the voltage or current must be gradually changed, by using the quasi-analogue Jog
control.
To enable the current limit to be set before connecting the load, the limit setting is displayed when
the output is off. Pressing the View Limits key at any time provides a temporary display of the limit
values allowing precise adjustment to also be made with the output on.
Setting Memories for Added Convenience
The XDL series provided storage of up to 10 Power supply sets-ups in non-volatile memory. Upon
mains switch-off, the set-up of the PSU is saved and is automatically restored at switch-on.
OVP and OCP Trips with 'Alarm' Output
The XDL series provides fully adjustable over-voltage and over-current trips which can be used
both as a fail-safe against accidental missetting and as a protection against inappropriate load
conditions. In addition to turning the output off, a trip condition switches the rear panel alarm
signal enabling other equipment to be controlled.
For complete protection of the Power supply, the trip will also be operated by over-temperature or
excess voltage on the sense terminals.
Handleidingen type:
Gebruikershandleiding
Pagina’s:
101
Grootte:
1.82 Mbytes (1903881 Bytes)
Taal:
english, german, french, spanish
Herziening:
4
Handleidingen-ID:
975-0107-01-04
Datum:
2008 05 01
Kwaliteit:
Elektronisch document, geen scan, zeer goed leesbaar.
Upload datum:
2019 08 18
MD5:
ab618476473b1604155ace204cd60320
Downloads:
720
Informatie
Introduction
Specification
EMC
Safety
Installation
Connections
Initial Operation
Manual Operation
Remote Operation /XDL 35-5P & XDL 56-4P only)
Remote Commands
Maintenance
Calibration
Instructions en Francais
Bedienungsanleitung auf Deutsch
Istruzioni in Italiano
Instrucciones en Español
Warranty Information