Fluke 4265A Voeding
Fabrikant:
Model:
4265A
Datum:
1976
Categorie:
Groep:
Omschrijving:
Binary Programmable Power Source

Informatie

The Model 4265A is a programmable, bipolar dc voltage source. Output voltage is from 0 to 65.532 vdc in two ranges; 16 and 65 vdc. Programming resolution using the internal reference voltage is 1 mv on the 16 volt range and 4 mv on the 65 volt range. Output accuracy is ±.01% of the programmed level on both voltage ranges. After a 100 /sec settling time, a READY/NOT READY FLAG indicates that the output has settled to ±.01% of the programmed increment for a resistive load. The output current is rated at ±1 ampere maximum and is limited to approximately ±1.1 ampere in the event of an overload or short circuit. The sink current (milliamps) is rated at 1000-10 Eout maximum. A Programmable Current Limiter (Option -06) is available to allow programming the maximum output current to a lower level. A current limit flag indicates when a sink or source current overload exists with or without the -06 Option. 1-3. Programming requirements are compatible with DTL or TTL logic levels. Contact or relay closures can also be used. The Voltage Source is programmed on the low range using straight binary coding. The high range is also programmed in the same manner, but the actual output is four times the programmed level. Two's complement coding is required for negative outputs when the Isolated Control Logic (—01 Option) is installed. All programming inputs and flag outputs are available through a 50 pin Amphenol, Blue Ribbon connector located on the rear panel. A +5 vdc output is also available at this connector and is used to provide power for external programming circuitry. Negative logic is employed for programming. The logic levelsi are as follows: Logic “0” = +2.0 vdc to +5.0 vdc or open circuit Logic “1” = 0 to +0.4 vdc or short circuit to LOGIC GRD. 1-4, Three options are available to provide tailoring of the Power supply to fit application requirements. These options are identified by numeric designations -03, -06, and -09. A description of each option is provided in Table 1-1. These options may be installed at the factory when the instrument is ordered or in the field at a later time. 1-5. Physically, the power source is completely solid state. Plug in printed circuit boards, with easy to reach test points and adjustments, are used for ease in servicing. The unit is forced air cooled. This results in lower component temperatures and thus higher reliability than would normally be obtained in a source of this power capability. The chassis is designed for bench top use, or it can be installed in a standard equipment rack by using the Accessory Rack Mounting Fixtures.

toon meer

Service-en gebruikershandleiding
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
120
Grootte:
4.65 Mbytes (4873699 Bytes)
Taal:
english
Herziening:
1
Handleidingen-ID:
310631
Datum:
Kwaliteit:
Gescand document alle leesbaar.
Upload datum:
2016 01 31
MD5:
cc08fc49321b70b3983c15fb5ce9bda2
Downloads:
743

Informatie

1 INTRODUCTION AND SPECIFICATIONS ... 1-1 1-1. Introduction ... ... 1-1 1-6. Specifications ... 1-2 2 OPERATING INSTRUCTIONS ... 2-1 2-1. Introduction ... 2-1 2-3. Shipping Information ... 2-1 2-6. Input Power ... 2-1 2-8. Rack Installation ... 2-1 2-10. Operating Features ... 2-3 2-12. Operating Notes ... 2-3 2-24, Programming Information ... 2-4 3 THEORY OF OPERATION ... 3-1 3-1. Introduction ... 3-1 3-3. Fundamental Circuit Description ... 3-1 3-5. Block Diagram Analysis ... 3-2 3-14. Circuit Descriptions ... 3-3 4 MAINTENANCE ... 4-1 4-1. Introduction ... 4-1 4-3. Service Information ... 4-1 4-6. General Maintenance ... 4-1 4-13. Maintenance Access ... 4-1 4-15. Calibration Procedures ... 4-2 5 LIST OF REPLACEABLE PARTS ... 5-1 Introduction ... 54 Parts List Column Descriptions ... 5-5 Manufacturers’ Cross Reference List Column Descriptions . 5-6 How to Obtain Parts ... 5-9 Serial Number Effectivity ... 6 OPTIONS AND Accessories ... 6-1 Introduction ... 6-3 Option Information ... 6-5 Accessory Information ... Model A4200 Manual Control Unit Schematic Diagram A4200-1000 Option -09, Multi-Strobe Isolated Logic Schematic Diagram 4200-1024 (2 sheets) Schematic Diagram 4200-1025 Rack Mounting Fixtures Program Connector Extender PCB assembly and Cable Extender Assembly 7 GENERAL INFORMATION ... 8 SCHEMATIC DIAGRAMS ... A1 Mother Board/A7 Binary Display 4265 A-1011 4265A-1013 A2 Power Supply/A10 Connector Board 4250A-1061 4250A-1012 A3 Preamplifier 4265A-1051 A4 Option -03, External Reference 4210A-1041 A5 Binary Ladder 4216A-1031 A6 Isolated Control Logic (2 sheets) 4275A-1021 A8 Option -06, Programmable Current Limiter 4250A-1081 A9 Power Amplifier 4250A-1071

toon meer