Kenwood - TS-440S - Ricetrasmettitore
Fabricante:
Immagine 1 di 1
Se disponete di altre foto o manuali per l'apparecchio
Kenwood TS-440S
è possibile
caricare i file qui.
Equipaggiamento:
TS-440S
Data:
1983
Categoria:
Gruppo:
Sottogruppo:
Informazioni
1. Wide dynamic range
New advances in circuit design have made a 102 dB dynamic
range (500 Hz IF bandwidth) possible.
2. General coverage reception from 100 kHz to 30 MHz
In addition to transmission and reception on all amateur
bands from 1.8 to 28 MHz, the TS-440S provides a continuous
tuning general coverage receiver with a range of 100 kHz to
30 MHz.
3. Automatic antenna tuner
The optional, built-in automatic antenna tuner will operate
from 3.5 to 28 MHz.
4. All-mode operation
USB, LSB, CW, AM, FM, and AFSK modes are provided.
5. 100% continuous duty transmit
Transmission at a 100% duty cycle is possible for relatively
long durations (one hour or less) in any mode, including FM
and AFSK.
6. CW full break-in
Full break-in operation is possible in the CW mode. Rapid
transmit/receive switching also makes the radio suitable for
data communications in the SSB mode, such as AMTOR.
7. Build-in XIT
XIT (Transmitter incremental tuning) allows fine tuning of
the transmitter frequency.
8. Switchable IF bandwidth
The IF bandswitch allows you to tailor the receiver
bandwidth to the operating conditions. Several selections
are provided; AUTO, W (Wide), M1 (Medium 1), M2 (Medium 2)
and N (Narrow). When the AUTO position has been selected the
radio will select the optimum bandwidth for the selected
mode of operation.
9. Switchable AGC time constant
A switch is provided to select either FAST or SLOW
AGC action.
10. All mode squelch
11. Built-in RF power/SWR meter
12. Versatile frequency control
• Accurate frequency selection is possible due to the use of
a single reference oscillator circuit.
• Continuous tuning of all frequencies thru the use of
digital VFO technology. The basic 10 Hz step tuning rate is
modified, according to the selected mode, for optimum tuning
speed and accuracy. An automatic fast scan function is also
provided.
• Dual, digital VFO's (A/B) enable crossband, cross mode
operation.
• 100-channel memory (including 10 odd-split channels)
stores the frequency, band, and mode.
• Memory scan and two programmable scan ranges.
• Direct entry of the desired frequency using the front
panel numeric keypad is also possible.
• A memory scroll function allows review of the memory
channel contents.
• Selection of the desired memory channel Ts possible using
either the TUNING dial or microphone UP/DOWN pushbuttons.
• The T-F SET function is useful for split frequency operation.
• An optional tone unit TU-8 may be used in conjunction with
the odd-split memory channels to allow 10 meter repeater
operations with CTCSS access.
• Optional computer interface.
• Built-in long-life memory back-up battery.
• 2-color fluorescent display tube indicates frequency and
other operational data.
13. Front panel control of the TUNING dial torque is provided.
2 Manuali
Manuale di servizio
Tipo di manuale:
Manuale di servizio
Pagine:
116
Dimensione:
24,5 MB
Lingua:
inglese
Revisione:
Revised
ID manuale:
B51-1919-00
Data:
Qualità:
Documento scansionato, tutto leggibile.
Data caricamento:
10 Luglio 2011
MD5:
f55547e3-297d-f9c0-cfbe-e01fe18f02f3
Downloads:
27920
Manuale di servizio
Tipo di manuale:
Manuale di servizio
Pagine:
57
Dimensione:
45,3 MB
Lingua:
inglese
Revisione:
ID manuale:
B50-8048-30(K, M, T, W)
Data:
Dicembre 1991
Qualità:
Documento scansionato, che si legge in parte male, in parte non si legge.
Data caricamento:
08 Gennaio 2017
MD5:
40b8cf3d-6f70-07f1-2f72-b6a07411fd6e
Informazioni
1.
FEATURES......................................................................
3
2.
INSTALLATION...........................................................
4
2-1.
PRECAUTIONS.......................................................
4
2-2. FIXED
STATION.................................................... 4
2-2-1.
Interconnection....................................................
4
2-2-2.
Grounding.............................................................
4
2-2-3.
Antenna.................................................................
5
2-2-4. Key
connection.................................................... 5
2-3.
MOBILE.....................................................................
5
2-3-1. Mounting bracket installation
.......................... 5
2-3-2. Power supply
connection.................................. 5
3.
OPERATION...................................................................
6
3-1. OPERATING CONTROLS................................... 6
3-1.-1. Front
panel............................................................
6
3-1-2. Rear
panel..........................................................
10
3-1 -3. Top
cover............................................................
11
3-2.
RECEIVE.................................................................
12
3-2-1. Initial
setting.......................................................
12
3-2-2. CW zero-beat
operation.................................. 12
3-2-3. Direct keyboard frequency entry.................. 13
3-2-4. AM
reception.....................................................
13
3-3.
TRANSMIT...........................................................
13
3-3-1. SSB (LSB, USB)
mode..................................... 13
3-3-2. CW
mode............................................................
14
(a) Semi-automatic break-in.......................... 14
(b) Full-automatic break-in............................. 14
3-3-3. FM
mode............................................................
14
• Subaudible tone............................................ 15
3-3-4. AM
mode............................................................
15
3-4. AUTOMATIC ANTENNA TUNER ............... 15
3-5. DUAL DIGITAL VFO's.................................... 15
3-5-1. Why two
VFO's................................................ 15
3-5-2. Split
frequency.................................................. 15
(a) A = B
switch................................................ 1 5
(b) A/B
switch................................................... 1 5
(c) SPLIT
switch.............................................. 15
(d) T-F SET switch.......................................... 15
3-6. MEMORY
..............................................................
16
3-6-1. Memory
entry.................................................... 16
3-6-2. Transferring memory information to the
VFO
.....................................................................
16
3-6-3. Transferring data between memory
channels.............................................................
17
3-6-4. Entering/Transferring data in the split
frequency channels.......................................... 17
3-6-5. Clearing a memory channel........................... 17
3-6-6. Memory
recall.................................................... 17
3-7. SCAN
......................................................................
17
3-7-1. Memory
scan..................................................... 17
3-7-2. Program
scan..................................................... 18
3-7-3. Scan
speed.........................................................
18
3-7-4. Memory channel
lockout................................. 18
3-8.
AFSK.......................................................................
19
3-8-1.
Reception............................................................
19
3-8-2.
Transmit.............................................................
19
3-8-3. AMTOR
operation............................................. 19
3-9. OPERATION WITH A LINEAR AMPLIFIER.. 19
4. CIRCUIT DESCRIPTION
....................................... 20
4-1. GENERAL DESCRIPTION................................ 20
4-2. TRANSMITTER SECTION.............................. 20
4-3. RECEIVER
SECTION......................................... 20
4-4. CIRCUIT BOARD DESCRIPTION................. 20
4-4-1. RF unit
(X44-1680-00)................................... 20
4-4-2. IF unit (X60-1
300-00)..................................... 20
4-4-3. Control unit (X53-1450-00).......................... 20
4-4-4. PLL unit (X
50-2050-00)................................ 20
4-4-5. Final unit
(X45-1470-00)............................... 20
4-4-6. Filter unit (X51-1
340-00)............................... 20
4-4-7. AT (Automatic Antenna Tuner) unit
(X57-1150-00)..................................................
20
5. MAINTENANCE AND ADJUSTMENT............ 21
5-1. GENERAL INFORMATION ............................. 21
5-2. SERVICE
...............................................................
21
5-3.
CLEANING............................................................
21
5-4. IN CASE OF DIFFICULTY.............................. 21
5-5. MICROPROCESSOR BACK-UP
LITHIUM BATTERY.......................................... 22
5-6. MICROPROCESSOR RESET.......................... 22
5-7. ORDERING SPARE PARTS........................... 22
5-8.
ADJUSTMENTS.................................................. 23
5-8-1. Cover
removal................................................. 23
5-8-2. Internal
views................................................. 23
5-8-3. Digital display
calibration............................ 24
5-8-4. Optional 10 Hz display resolution.............. 24
5-8-5. CW zero beat frequency selection............ 24
5-8-6. Side tone
level............................................... 25
5-8-7. Beep tone
selection....................................... 25
5-8-8. Beep tone
level.............................................. 25
5-8-9. Tuning dial
torque.......................................... 26
5-8-10. Linear amplifier
control................................ 26
6. OPTIONAL ACCESSORIES................................. 27
6-1. CRYSTAL FILTER INSTALLATION............ 27
6-2. VOICE SYNTHESIZER UNIT VS-1
INSTALLATION
.................................................. 28
6-3. INTERFACE IC KIT IC-10
INSTALLATION
.................................................. 29
6-4. OTHER ACCESSORIES................................... 30
7. BLOCK
DIAGRAM................................................... 33
8. SCHEMATIC DIAGRAM....................................... 34
9. SPECIFICATIONS AND ACCESSORIES........ 41
9-1.
SPECIFICATIONS............................................... 41
9-2.
ACCESSORIES...................................................
42
10.
REFERENCE...............................................................
43
10-1. ANTENNA INSTALLATION........................ 43
10-1-1. Fixed
station.................................................... 43
10-1-2.
Mobile................................................................
43
10-2. MOBILE OPERATION.................................... 44
10-2-1.
Installation........................................................
44
10-2-2. Noise
reduction.............................................. 45
10-2-3. Battery
capacity............................................. 45
10-3. RADIO FREQUENCY ALLOCATION........ 46
Downloads:
2826