Fluke PM3384 Oscilloscopes
Digital Storage/Analog Oscilloscope
There are four models in this family of Fluke
Each of these models is a combination of an analog real-time
and a fully featured digital storage
oscilloscope. By pressing a single push button, you can
switch the instrument from the analog mode to the digital
mode and back. This allows each of the units to be used in
an optimum operating mode for all kinds of signal
conditions. Complex data streams, modulated waveforms, and
video signals can often best be seen in the analog mode of
operation. The digital mode of operation is more suited for
single events, signals with low repetition frequencies, and
when automatic measurements need to be performed. In this
family there is a choice of four models. Two models have a
bandwidth of 200 MHz; the two others have a bandwidth of 100
MHz. There is a choice of two models with four fully
featured channels or four channels in a ’2+2’ configuration.
In the same instrument family, there are two 200-MHz analog
oscilloscopes that have specifications similar to the
above-mentioned analog/digital combination oscilloscopes
operating in analog mode.
All analog/digital combination oscilloscopes listed above
have the following features:
- 8K sample acquisition memory, expandable to 32K.
- Up to 40 waveforms stored in memory or 204 waveforms with
optional memory extension.
- Autoset function for an instant optimized signal display
at the touch of a button.
- Cursor measurements with 1% accuracies.
- Extensive set of fully automated voltmeter and time
- Probe operated Touch Hold and Measure’ function freezes
the display and instantly displays the signal frequency,
amplitude and dc voltage level.
- Peak detection for the capture of glitches as narrow as 5 ns.
- Pattern, State and Glitch triggering (2 ns)
- Event delay and pretriggering and posttriggering.
- TV triggering including HDTV and TV line selection.
- Serial Interface
for printing and plotting.
- Averaging to reduce signal noise and to increase the
vertical resolution from 8 to 16 bits.
- Advanced mathematics, including digitai low-pass
filtering. A Math+ option adds integration, differentiation,
histogramming, and (as part of a option) FFT.
- Sine interpolation and magnification which enables true to
life four channel single shot acquisitions with a timebase
up to 625 ns/div (32x magnified)
- A delayed timebase with full trigger features.
- An RS-232 (EIA-232-D) Interface
(standard) and an
- Autocal for automatic fine tuning of all circuitry to
achieve maximum accuracy under all user conditions.
- Closed case calibration for efficient maintenance of
traceable calibration at minimum cost.
The following options are available:
- A MATH+ option with more automated measurement functions
including envelope and measurement pass/fail testing. Also
included in this option are Integration, Differentiation,
Histogramming, and FFT.
- Memory extension offering 32K acquisition length and the
ability to store 204 traces (of 512 samples each) in memory.
- IEEE-488.2 Interface
using the new SCPI (Standard Commands
for Programmable Instruments) industry standard for remote
control of test and measurement equipment.
Manuel de l'utilisateur
28.83 Mbytes (30234029 Bytes)
4822 872 00551 and/or 930501
01 janvier 1993
Document scanné, tous les lisible.
Date de transfert:
20 janvier 2018
INSIDE THIS MANUAL
This operating guide contains information on all of the
oscilloscope’s features. It
starts with a general introduction, a summary of main
inspection note and a front and rear view.
Operators safety Chapter 1 should be read before unpacking,
installing, and operating the instrument.
Installation instructions Chapter 2 describes grounding,
line cord, fuses,
and backup batteries.
Getting started Chapter 3 provides a 10-minute tutorial intended
for those who are not familiar with Fluke
How to use more advanced Chapter 4 provides the more
functions of the instrument with a detailed explanation of
the major functions
of the Oscilloscope
Function reference Chapter 5 contains an alphabetized
each function. Each description includes an
explanation of local and remote control functions.
CPL protocol Chapter 6 provides the CPL commands with an
example of each.
Function index The Function Index lists all implemented
functions in alphabetical order.
Index The overall index contains all function names
and reference words in alphabetical order. It
includes the relevant chapter and page number
where more detailed information can be found.
IN THE APPENDICES
RS-232 Cable configurations