Wavetek 184 Générateur
Fabricant:
Image 1 de 1
Si vous avez d'autres photos ou manuels pour les
Wavetek 184 vous pouvez télécharger les fichiers ici .
Modèle:
184
Date:
1980
Catégorie:
Groupe:
Description:
5MHz Sweep Generator
Information
THE MODEL 184
Wavetek model 184, the 5 MHz Sweep Generator, is a precision
source of sine, triangle, square, positive pulse and
negative pulse waveforms plus dc voltage. Frequency of the
waveforms is manually and remotely variable from 100µHz to 5
MHz.
The Generator can repetitively sweep between two
individually set frequencies and at a particular sweep rate.
The amplitude of waveforms is variable from 20V p-p, open
circuit maximum, to —80 dB.
DC reference of the waveforms can be offset positively and
negatively.
The symmetry of the waveforms is continuously adjustable
from approximately 1:19 to 19:1. Varying symmetry provides
variable duty cycle pulses, sawtooth and asymmetrical sine
waveforms.
A voltage representing Generator frequency, a
fixed-amplitude pulse train of that frequency, and a voltage
ramp representing frequency sweep rate are provided as front
panel outputs.
Type manuel:
manuel de réparation
Pages:
13
Taille:
1.48 Mbytes (1553568 Bytes)
Langue:
english
Révision:
Manuel-ID:
Date:
1975 01 01
Qualité:
Document scanné, en lisant mal, en partie illisible.
Date de transfert:
2020 12 30
MD5:
0801980429978faf14241e7b11cd5671
Téléchargements:
611
Information
Calibration Procedure
Type manuel:
Service et Manuel de l'utilisateur
Pages:
52
Taille:
1.59 Mbytes (1672042 Bytes)
Langue:
english
Révision:
Manuel-ID:
Date:
1980 02 01
Qualité:
Document scanné, la lecture en partie mal, en partie illisible.
Date de transfert:
2018 08 13
MD5:
0bc85881272d20be9947e91dcbc07846
Téléchargements:
552
Information
1.1 THE model 184 ... 1-1
1.2 SPECIFICATIONS ... 1-1
SECTION 2 INITIAL PREPARATION
2.1 UNPACKING INSPECTION ... 2-1
2.2 PREPARATION FOR USE ... 2-1
2.3 ELECTRICAL ACCEPTANCE CHECK ... 2-1
SECTION 3 OPERATION
3.1 CONTROLS AND CONNECTORS ... 3-1
3.2 OPERATION ... 3-4
3.2.1 Signal Termination . ... 3-4
3.2.2 Continuous Operation ... . 3-5
3.2.3 Trigger Mode ... 3-5
3.2.4 Triggering ... 3-6
3.2.5 GATED (or Tone Burst) Mode ... 3-6
3.2.6 SWEEP Mode ... 3-6
3.2.7 Voltage Control - VCG ... 3-6
SECTION 4 CIRCUIT DESCRIPTION
4.1 VOLTAGE CONTROL LED GEN ERATO ft ... 4-1
4.2 SWEEP Generator ... 4-2
SECTION 5 CALIBRATION
5.1 FACTORY REPAIR ... 5-1
5.2 REQUIRED TEST EQUIPMENT ... 5-1
5.3 REMOVING Generator COVER ... 5-1
5.4 CALIBRATION ... 5-1
SECTION 6 TROUBLESHOOTING
6.1 INTRODUCTION ... 6-1
6.2 CIRCUIT BOARD ACCESS ... 6-1
6.3 BASIC TECHNIQUES ... 6-1
6.4 TROUBLESHOOTING INDIVIDUAL COMPONENTS ... 6-1
6.5 TROUBLESHOOTING GUIDE ... 6-2
SECTION 7 PARTS AND SCHEMATICS
7.1 DRAWINGS ... 7-1
7.2 ORDERING PARTS ... 7-1
7.3 ADDENDA ... 7-1