Hewlett Packard 13OB Osciloscopio
Fabricante:
Imagen 1 de 1
Si tienes otras fotos o manuales para el
Hewlett Packard 13OB puedes subir los archivos aquí .
Modelo:
13OB
Fecha:
1959
Categoría:
Grupo:
Descripción:
Información
The Hewlett-Packard Model 130B Oscilloscope is a general
purpose Oscilloscope, it can be used with either internal or
external sweeps which can be either internally or externally
synchronized and it can be obtained in either the cabinet or
rack type mounting. Because of its high sensitivity and
balanced input, the Model 130B may often be used directly
with transducers, enabling you to see a direct presentation
of phenomena desired without having to resort to preamplifiers.
Some of the special features of this Oscilloscope are as
follows:
A. LINEAR INTEGRATOR SWEEP Generator
The accurate direct reading sweeps are obtained from a
Miller-integrator sweep circuit which insures a high order
linearity and stability. This type of sweep Generator, is
more reliable and independent of tube characteristics than
other types of sweep Generator.
B. X5 SWEEP EXPANSION
You speed observation and analysis of transients by
expanding a two centimeter segment of the trace to 10
centimeters for easy viewing of detail. This X5 sweep
expander, may be used on all sweep time settings and expands
the fastest sweep time to .2 microsecond/cm.
C. CALIBRATED AMPLIFIERS
Voltage measurements of various waveforms are quickly made
with the 130B, accurate within ±5%. A built-in Calibrator
which is accurate within ±2% permits quick verification and
standardization of the Amplifier gain.
Phase shift measurements can be made accurately with this
Oscilloscope over a wide range of input frequencies.
Type manuel:
Manual de servicio
Páginas:
66
Tamaño:
18.94 Mbytes (19860989 Bytes)
Idioma:
english
Revisión:
Manuel-ID:
00013-3
Fecha:
Formato:
Documento Scaned, todo legible.
Fecha de subida:
2015 05 31
MD5:
d6a1eabdd737e1e71f14e9fb66125897
Descargas:
1416
Información
SERIALS PREFIXED: 201
Section Page
I GENERAL DESCRIPTION ... 1-1
1-1. General ... 1-1
1-2. Damage in Transit ... 1-1
1-3. Power Line Voltages ... 1-1
1-4. Power Cord ... 1-1
1-5. Installation of Rack Mount ... 1-1
1-6. Cathode Ray Tube Warranty ... 1-2
II OPERATING INSTRUCTIONS ... 2-1
2-1. Controls and Terminals ... 2-1
2-2. Rear-Access Terminals ... 2-1
2-3. Warm-Up Drift ... 2-1
2-4. AC or DC Coupling ... 2-2
2-5. Balanced Inputs ... 2-2
2-6. Operating Procedures ... 2-2
III THEORY OF OPERATION ... 3-1
3-1. General Content ... 3-1
3-2. Over-A 11 Operation ... 3-1
3-3. Vertical Amplification Channel . . 3-1
3-4. Horizontal Amplification
Channel ... 3-2
3-5. Sweep Generator ... 3-2
3-6. Low Voltage Power supply ... 3-3
III THEORY OF OPERATION (cont’d)
3-7. High Voltage Power supply ... ... 4-3
4-5. Connecting for 230 Volt Operation. 4-3
4-6. Tube Replacement ... 4-4
4-7. Condensed Test and Adjustment
Procedures ... 4-5
4-8. Adjustment Procedure ... 4-9
4-9. TurnOn ... · ... 4-9
4-10. Power Supplies ... 4-9
4-11. Replacing and Adjusting the CRT. . 4-11 4-12. Checking
and Adjusting the
Calibrator ... 4-13
4-13. Adjusting the Vertical Amplifier . 4-13
4-14. Adjusting the Horizontal Amplifier 4-15
4-15. Phase Shift Adjust ... 4-15
4-16. Adjusting Preset ... 4-17
4-16. Adjusting the Sawtooth Generator
and Sweep Amplifier ... 4-17