Información del equipo:

AVO THE “AVO” VALVE CHARACTERISTIC METER Válvula metros característica
Categoría: Los instrumentos de medición
Grupo: Válvula metros característica
                                    'The problem of designing a Valve Testing Instrument capable
of giving a true and comprehensive picture of the state of
any valve, has always been one of considerable magnitude,
increasing in complexity as new valve types are brought into
general use.
For a quick general purpose test necessitating a minimum of
time and technical effort a mutual conductance figure will
give an adequate idea of a valve’s usefulness, and the
original “ AVO ” Valve Tester was designed to test the
efficiency of valves on this basis.
Whilst a Valve Tester must, of necessity, be accompanied by
a data book correlating the results of the Tester with the
condition of the valve in question, a purely empirical
figure, if used as a standard, will always give rise to
doubts in the mind of the operator. The instrument should
therefore, produce a figure which can be compared with some
standard quoted by the valve manufacturer, if the operator
is to use his instrument with confidence. For this reason
the “ AVO ” Valve Tester used the static zero bias mutual
conductance figure as a basis of comparison, this figure
being at that time almost universally quoted by the valve
In order to reproduce this standard correctly, it was also
necessary to reproduce the stated values of DC anode and
screen voltage, a matter of some considerable difficulty
when it is realised that for any stated condition of anode
and/or screen volts the corresponding electrode currents can
vary over very wide limits, and in the case of valves of low
initial anode current and high slope, the actuation of the
control which produces the milliamp-per-volt reading might
easily double the anode current flowing. With DC methods of
testing the inherent internal resistance of the rectifying
circuits used could be such as to give regulation errors
which could cause results to be meaningless unless
complicated thermionic stabilising circuits and a vast array
of monitoring meters were used in all voltage supply
circuits. Such complications would not only render the
Tester of prohibitive price and size, but would considerably
increase the complication of operation for the non-technical
The problem was overcome by the introduction of the AC
method of operation (Patent No. 480752) by which means the
necessary DC test conditions were correctly simulated and a
true mutual conductance figure produced by the application
of AC voltages of suitable amplitude to all electrodes. This
enormously simplified the Power supply problem, rendered
regulation errors negligible, and obviated the necessity for
voltage circuit monitoring. The “ AVO” Valve Tester thus
fulfilled normal testing needs for a longperiod.
During recent years, however, electronic techniques have
become much more precise and the nature and multiplicity of
valve types have continuously increased. The zero bias
mutual conductance figure is seldom quoted by the valve
manufacturers, who, usually now publish the optimum working
point mutual conductance and voltage figures, and in a large
number of cases give full families of curves, from which,
precise operation, under a variety of working conditions,
can be judged. To cater for present day requirements
therefore, a valve testing device should not only be capable
of producing a working point mutual conductance figure at
any reasonable value of anode, screen or grid voltage
recommended by the manufacturers, but should also be
capable, if necessary, or reproducing any one of the mutual
characteristics associated with the valve in question.

Estos manuales están disponibles para el equipo anterior:

Tipo de manual: Servicio y Manual del usuario AVO-5994-Manual-Page-1-Picture
Páginas: 28
Tamaño: 1.57 Mbytes (1642266 Bytes)
Idioma Inglés
Manual-/ número de identificación:
Calidad: Documento Scaned, todo legible.
Fecha de carga:
MD5: 4e28d5c4286622db7b513db57f51eba8
Descargas: 450 desde 09 mayo 2014
Foreword ... 
 ...  7
The Basic Method of checking diodes and
rectifiers ...  8
The Protective Relay
 ...  9
The Valve Panel and Selector Switch
Procedure for setting up valve base connections
 ...  10
Provision for new valve bases
The prevention of Self oscillation of valves under
test ...  12
Diagram of Standard base pin connections
 ...  13
Procedure for valves having internally connected
pins ...  14
The controls on the front panel, their functions and
operations  ...  14
The Set ~ Control
The Leakage Switch  ... 
, ... 
The Circuit Selector Switch
The Anode and Screen Voltage Switches
 ...  16
The Heater Voltage Switches
 ...  16
The Negative Grid Voltage Controls
The Backing Off Controls
The Meter Switch
The Set mA/V Control
The Electrode Selector Switch
The Mains Adjustment Panel at the rear of the
Instrument ...  17
General Procedure for testing a
valve ...  21 Multiple diodes and rectifiers—double
triodes, double pentodes and double tetrodes— combined diode
and amplifying valves—frequency changers of heptode and
hexode types —frequency changers employing separate
electrode assemblies.
The Use of the Links on the Valve Panel of the Instrument
 ...  23
Tuning Indicators (Magic
Eyes) ... 
Rectifiers ... 
Cold Cathode
Rectifiers ... 
Thyratrons ... 
Neon Indicators
 ...  25 Abbreviated Working Instructions
for the “ AVO ” Valve characteristic meter
Ill ... 
Circuit diagram of Valve Characteristic Meter

Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
Captcha Image
Powered by Commentics