Xantrex XPH 35-4T Power supply
Manufacturer:
No picture available!
Maybe you can upload a photo for the
Xantrex XPH 35-4T ?
If you have any other manuals for the
Xantrex XPH 35-4T you can upload the files here .
Model:
XPH 35-4T
Date:
2008
Category:
Group:
Description:
Dual and Triple Output 35V 4A DC Power Supply
Information
The XPH 35-4D and XPH 35-4Tv provide high levels of power (up to 305 watts) in a compact and
attractive case style.
High resolution controls allow precise setting of voltage and current levels which are indicated on
accurate and legible digital meters.
Excellent line and load regulation are matched by low noise and good transient response. High
power efficiency ensures that the unit remains cool without any fan noise.
The XPH 35-4D has two independent and isolated outputs each with a 0 to 35V, 0 to 4A
capability. The outputs operate in constant voltage or constant current mode with automatic cross-
over and mode indication. Each output has its own on-off switch. Where higher voltages or
currents are required the outputs can be wired in either series or parallel to provide voltages up to
70 volts or currents up to 8 Amps.
The XPH 35-4T has, in addition, an Auxiliary ‘logic voltage’ output with a 5A current capability. To
reflect the increasing usage of low-voltage logic devices, this output can be preset between
1.5 volts and 5 volts via a front panel control.
The total power capability is 280 watts for the dual supply and 305 watts for the triple.
The XPH series incorporates separate digital voltage and current meters on each main output.
The meters use bright 14mm (0·56”) LED displays and have an update rate of 4 per second
providing near instantaneous response. Simultaneous metering of voltage and current provides
accurate information “at a glance” and avoids any possibility of misinterpretation. When an output
switch is set to “off”, the current limit setting is displayed enabling conditions to be set before the
load is connected. With the right-hand main output off, the right-hand meters can be used to
momentarily display the preset Auxiliary voltage and current limit.
The XPH series has been designed to meet the stringent requirements of relevant IEC standards
for safety and EMC, including harmonics emissions. All outputs are intrinsically short circuit proof,
and are protected against external voltages and reverse currents.
Manual type:
User Manual
Pages:
37
Size:
577.59 Kbytes (591455 Bytes)
Language:
english, german, french, italian, spanish
Revision:
4
Manual ID:
975-0101-01-04
Date:
2008 04 01
Quality:
Electronic document, no scan, very well readable.
Upload date:
2019 08 18
MD5:
c8261b85af42d4aa3f24c104c5228f60
Downloads:
606
Information
Introduction
Specification
EMC
Safety
Installation
Connections
Operation - Main Outputs
Operation - Auxiliary Output
Operation - General
Calibration
Maintenance
Instructions en Francais
Sécurité
Installation
Connexions
Fonctionnement - Sorties principales
Fonctionnement – Sortie Auxiliaire
Fonctionnement - Généralités
Maintenance
Bedienungsanleitung auf Deutsch
Sicherheit
Installation
Anschlüsse
Betrieb - Hauptausgänge
Betrieb – Hilfsausgang
Betrieb - Allgemein
Wartung
Istruzioni in Italiano
Sicurezza
Installazione
Collegamenti
Funzionamento - Uscite principali
Funzionamento – Uscita Ausiliaria
Funzionamento - Generale
Manutenzione
Instrucciones en Español
Seguridad
Instalación
Conexiones
Operación - Salidas Principales
Operación – Salida Auxiliar
Operación - General
Mantenimiento
Warranty Information