Wavetek 1004-1 Generator
Manufacturer:
No picture available!
Maybe you can upload a pic for the
Wavetek 1004-1 ?
If you have any other manuals for the
Wavetek 1004-1 you can upload the files here .
Model:
1004-1
Date:
1977
Category:
Group:
Description:
SWEEP/SIGNAL GENERATOR
Information
The Wavetek 1000 Series Sweep/Signal generators are single
band instruments covering the frequency range from 500 KHz
to 1.4 GHz. All units utilize the same, Front Panel, Harness
and Power supply with the balance of the circuits contained
in Plug-In Modules. However, it is not intended that one
model be converted
to another. The Plug-In concept simplifies maintenance
problems and provides marker circuits which can be
customized to specific applications. A Rear Panel Con nector
permits remote programming of Center Frequency, Sweep Width
and Output Level, plus. External Amplitude and Frequency
Modulation.
Manual type:
Service and User Manual
Pages:
77
Size:
5.97 Mbytes (6263685 Bytes)
Language:
english
Revision:
revised
Manual-ID:
Date:
Quality:
Scanned document, all readable.
Upload date:
09 November 2014
MD5:
bb6322721f7d6c0b5456cad22d34d599
Downloads:
3687
Information
This manual provides descriptive material and instructions
for the installation, operation, maintenance, and repair of
the Wavetek Model 1001A to 1005 Sweep/Signal Generator.
SECTION 1 -GENERAL INFORMATION
1.1 INTRODUCTION
1.2 SPECIFICATIONS
1.3 OPTIONS
1.4 Accessories
SECTION 2-INSTALLATION
2.1 MECHANICAL INSTALLATION
2.2 ELECTRICAL INSTALLATION
SECTION 2—OPERA TING INSTRUCTIONS
31 INTRODUCTION
3.2 DESCRIPTION OF FRONT PANEL
3.3 DESCRIPTION OF REAR PANEL
3.4 TYPICAL OPERATING SET UP
3.5 SPECIAL OPERATING NOTES
3.6 PROGRAMMING
SECTION 4 - CIRCUIT DESCRIPTION
4.1 INTRODUCTION
4.2 SIMPLIFIED BLOCK DIAGRAM
4.3 Power supply
4 4 SWEEP RATE (MODULE M1H)
4.5 SWEEP DRIVE (MODULE M2G)
4.6 SWEEP Oscillator FOR MODEL 1001A and 1002 (MODULE M9G
and M9H)
4 7 OUTPUT Amplifier FOR MODEL 1001A and 1002 (MODULE M1 OF
and M10G)
4.8 SWEEP Oscillator FOR MODEL 1003 1004, and 1005 (MODULE
M9R S and'T)
49 MARKER ADDER (MODULE M5G)
4.10 MARKERS (MODULE M6s)
SECTION 5 MAINTENANCE
5.1 INTRODUCTION
5.2 SERVICE INFORMATION
5.3 PERFORMANCE CHECKS
5.4 CALIBRATION PROCEDURE
5.5 TROUBLESHOOTING
SECTION 6 -SCHEMATICS & PARTS LIST
6.1 INTRODUCTION
6.2 MANUFACTURERS CODE
6.3 SCHEMATIC NOTES
6.4 ABBREVIATION CODE SCHEMATICS AND PARTS LIST
Add Comment
Terms and Conditions
These terms and conditions contain rules about posting comments. By submitting a comment, you are declaring that you agree with these rules:
- Although the administrator will attempt to moderate comments, it is impossible for every comment to have been moderated at any given time.
- You acknowledge that all comments express the views and opinions of the original author and not those of the administrator.
- You agree not to post any material which is knowingly false, obscene, hateful, threatening, harassing or invasive of a person's privacy.
- The administrator has the right to edit, move or remove any comment for any reason and without notice.
Failure to comply with these rules may result in being banned from further commenting.
These terms and conditions are subject to change at any time and without notice.
Comments