Krohn-Hite Corporation 30A-1 Filter
Manufacturer:
No picture available!
Maybe you can upload a pic for the
Krohn-Hite Corporation 30A-1 ?
If you have any other manuals for the
Krohn-Hite Corporation 30A-1 you can upload the files here .
Model:
30A-1
Date:
Category:
Group:
Description:
LOW-PASS ELLIPTICAL PLUG-IN FILTER MODULE
Information
INTRODUCTION
The model 30A Series are low-pass, 7-pole, 6-zero elliptical Plug-In filters providing
115dB/octave roll-off, a minimum stopband attenuation of >80dB, and a typical passband ripple
of 0.22dB peak-to-peak. The Model 30A-1 covers the range from 1Hz to 99kHz. The Model
30A-2 operates from 0.1Hz to 9.9kHz and from 0.01Hz to 990Hz in the Model 30A-3,
With its 115dB/octave rolloff rate, the model 30A provides a much narrower transition region
than an 8-pole Butterworth, and much less passband attenuation near cutoff. The transition
region from –3dB to –85dB is 64% of fc (cutoff), compared to 242% for the 8-pole Butterworth.
From –0.3dB to –85.6dB, it becomes 70% of fc compared to 404%. This permits lower sampling
rates and wider bandwidths, resulting in lower total system costs.
The model 30A Series is part of an ever expanding line of Plug-In Filter cards for use in the
Model 3905C and 3916C Mainframes, which accommodates 5 to 16 Filter cards respectively.
Manual type:
User Manual
Pages:
22
Size:
704.60 Kbytes (721511 Bytes)
Language:
english
Revision:
Manual-ID:
Date:
Quality:
Electronic document, no scan, very well readable.
Upload date:
17 January 2021
MD5:
b5f174fd83e0e467dbcd271c28005126
Downloads:
626
Information
GENERAL DESCRIPTION ... 1-1
1.1
INTRODUCTION ... 1-1
1.2
SPECIFICATIONS ... 1-1
2.0
OPERATION ... 2-1
INTRODUCTION ... 2-1
TURN-ON PROCEDURE ... 2-1
SELF-TEST FEATURE ... 2-1
FRONT PANEL CONTROLS and DISPLAY ... 2-2
Filter CHARACTERISTICS ... 2-3
2.5.1 Introduction ... 2-3
2.5.2 Normalized Ripple Response ... 2-3
VARIABLE BANDPASS and BAND REJECT OPERATION ... 2-3
TRANSIENT RESPONSE ... 2-4
PHASE RESPONSE ... 2-5
DELAY TIME ... 2-6
GROUP DELAY ... 2-6
3.0
IEEE-488 STD (GPIB) PROGRAMMING ... 3-1
3.1
INTRODUCTION ... 3-1
3.2
Filter TYPE ... 3-1
3.3
MODE OF OPERATION ... 3-1
3.4
DEVICE CLEAR ... 3-1
ACCEPTANCE ... 4-1
INTRODUCTION ... 4-1
TEST EQUIPMENT REQUIRED ... 4-1
PRE-FILTER, POST-FILTER AND UNITY GAIN ACCURACY ... 4-1
PASSBAND GAIN AND DISTORTION TESTS ... 4-2
4.4.1 Low Bands Ripple Response ... 4-2
4.4.2 High Band Ripple Response (Model(30A-1) ... 4-2
4.4.3 High Band Ripple Response (Model(30A-2) ... 4-3
4.4.4 High Band Ripple Response (Model(30A-3) ... 4-3
STOPBAND ATTENUATION ... 4-3
4.5.1 Band 1 ... 4-3
4.5.2 Band 2 ... 4-3
4.5.3 Band 3 ... 4-3
4.5.4 Band 4 ... 4-4
CUTOFF FREQUENCY ... 4-4
NOISE MEASUREMENTS ... 4-4
Add Comment
Terms and Conditions
These terms and conditions contain rules about posting comments. By submitting a comment, you are declaring that you agree with these rules:
- Although the administrator will attempt to moderate comments, it is impossible for every comment to have been moderated at any given time.
- You acknowledge that all comments express the views and opinions of the original author and not those of the administrator.
- You agree not to post any material which is knowingly false, obscene, hateful, threatening, harassing or invasive of a person's privacy.
- The administrator has the right to edit, move or remove any comment for any reason and without notice.
Failure to comply with these rules may result in being banned from further commenting.
These terms and conditions are subject to change at any time and without notice.
Comments