Ametek Advanced Measurement Technology 5113 Amplifier
Manufacturer:
Model:
5113
Date:
2002
Category:
Group:
Description:
Low Noise Preamplifier

Information

The Model 5113 Low-Noise Preamplifier provides high gain, low-noise amplification of wideband signals from DC to 1 MHz, well suited for use with both SIGNAL RECOVERY and other manufacturers’ signal processing instruments. Adjustable high and low frequency rolloffs allow the bandwidth to be reduced. Two inputs, with switchable coupling, allow either differential or single-ended operation. Coarse gain is selectable from x5 to x50,000 in a 1-2-5 sequence with a fine gain control extending the range to xl to X 10,000. An uncalibrated vernier allows finer adjustment of the gain. The unit may be powered either from an external DC power supply or from its internal sealed and maintenance-free lead-acid batteries. These batteries recharge automatically when a suitable external Power supply is connected. Other features include an overload fast-recovery button, a front-panel DC zero screwdriver control, and a battery test facility.

show more

User Manual
Manual type:
User Manual
Pages:
39
Size:
287.92 Kbytes (294830 Bytes)
Language:
english
Revision:
Manual ID:
222144
Date:
01 January 2002
Quality:
Electronic document, no scan, very well readable.
Upload date:
03 September 2016
MD5:
8fc2006b0be9beda788767712993bef7
Downloads:
213

Information

Chapter One, Introduction 1.1 Model 5113 Preamplifier ... 1-1 1.2 Why use a Preamplifier? ... 1-1 Chapter Two, Installation & Initial Checks 2.1 Installation ... 2-1 2.1.01 Introduction ... 2-1 2.1.02 Inspection ... 2-1 2.2 Initial Checks ... 2-1 2.2.01 Introduction ... 2-1 2.2.02 Equipment Required ... 2-1 2.2.03 Procedure ... 2-2 Chapter Three, Front and Rear Panels 3.1 Front Panel ... 3-1 3.1.01 INPUT Connectors ... 3-1 3.1.01 INPUT COUPLING Button ... 3-1 3.1.03 RECOVER/Sleep Button ... 3-2 3.1.04 GAIN (VERNIER) Control ... 3-2 3.1.05 LF ROLL-OFF (SLOPE) Control ... 3-3 3.1.06 HF ROLL-OFF (SLOPE) Control ... 3-3 3.1.06 POWER Switch ... 3-4 3.1.07 OUTPUT Connector ... 3-4 3.2 Rear Panel ... 3-4 Chapter Four, Front Panel Operation 4.1 Introduction ... 4-1 4.2 Operation ... 4-1 4.2.01 Power ... 4-1 4.2.02 Signal Grounding ... 4-1 4.2.03 Signal Voltage and Gain ... 4-1 4.2.04 DC Zero Adjustment ... 4-2 4.2.05 Overload Fast Recovery ... 4-2 4.2.06 Input Mode Selection ... 4-2 4.2.07 Filter Selection ... 4-2 4.2.08 Filter Roll-Off ... 4-3 4.2.09 Special Pages ... 4-3 4.2.10 Battery Operation, Test and Charging ... 4-4 Chapter Five, Computer Operation 5.1 Introduction ... 5-1 5.2 Operation ... 5-1 5.2.01 Overview ... 5-1 5.2.02 RS232 Interface - General Features ... 5-1 5.2.03 Choice of Baud Rate ... 5-2 5.2.04 RS232 Interface - Command Format ... 5-2 5.2 Command Descriptions ... 5-3 Appendix A, Specifications Appendix B, Pinouts Appendix c, Power supply Index Warranty ... End of Manual

show more

Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Captcha Image