Wavetek 187 Generator
Hersteller:
Modell:
187
Datum:
0
Kategorie:
Gruppe:
Beschreibung:
4 MHz PULSE/ FUNCTION GENERATOR

Information

The Wavetek model 187, a 4 MHz Pulse/Function Generator, is a precision source of sine, triangle, square and pulse waveforms plus dc voltage. All waveforms are front panel variable from 4 mHz to 4 MHz and can be frequency modulated and swept with an external signal. Variable width and delay, single or double pulses can be output inverted or normal. Amplitude of the waveforms is variable from 10V peak-to-peak into 50Ω down to 30 mV peak- to-peak. DC reference of the waveform can be offset positively or negatively. The two selectable waveform outputs are a 20V peak- to-peak maximum and a 2V peak-to-peak maximum (20 dB down from 20 Vp-p); both may be varied over a 30 dB range. A TTL level signal at Generator frequency is simultaneous with the waveform outputs for synchronization.

mehr

Service- und Bedienungsanleitung
Dokumenttyp:
Service- und Bedienungsanleitung
Seiten:
66
Größe:
12.21 Mbytes (12805318 Bytes)
Sprache:
english
Revision:
Dokument-ID:
Datum:
Qualität:
Gescanntes Dokument, alles ist lesbar.
Upload Datum:
2014 11 17
MD5:
7c28d0357c7ae2cfa8bc54ebdab80d54
Downloads:
1111

Information

SECTION 1 GENERAL DESCRIPTION 1.1 THE MODEL 187 ... -|_1 1.2 SPECIFICATIONS ... -|_1 1.2.1 Versatility ... 1_1 1.2.2 Frequency Precision ... 1-2 1.2.3 Amplitude Precision ... 1_2 1.2.4 Function Characteristics ... 1-2 1.2.5 General ... 1_2 SECTION 2 INITIAL PREPARATION 2.1 MECHANICAL INSTALLATION ... 2-1 2.2 ELECTRICAL INSTALLATION ... 2-1 2.2.1 Power Connection ... 2-1 2.2.2 Signal Connections ... 2-1 2.3 ELECTRICAL ACCEPTANCE CHECK ... ... 2-1 2.4 CHANGING THE OUTPUT IMPEDANCE ... 2-2 SECTION 3 OPERATION 3.1 CONTROLS AND CONNECTIONS . . 3-1 3.2 OPERATION ... 3.4 3.2.1 Signal Termination ... 3.4 3.2.2 Manual Function Generator Operation ... 3-4 3.2.3 Voltage Controlled Function Generator Operation ... 3-4 3.2.4 Pulse Generator Operation ... 3.5 SECTION 4 CIRCUIT DESCRIPTION 4.1 INTRODUCTION ... 4.·) 4.2 Generator BOARD ... 4-! 4.3 PULSE BOARD ... 4.2 4.3.1 Square ... 4.3 4.3.2 Delay Off ... 4.3 4.3.3 Delay On ... 4.3 SECTION 5 ALIGNMENT 5.1 FACTORY REPAIR ... 5^ 5.2 REQUIRED TEST EQUIPMENT ... 5-1 5.3 REMOVING Generator COVERS . . 5-1 5.4 ALIGNMENT ... 5-1 iii SECTION 6 TROUBLESHOOTING 6.1 FACTORY REPAIR ... 6'1 6.2 BEFORE YOU START ... 6'1 6.3 STARTING ... 6'3 6.4 TROUBLESHOOTING INDIVIDUAL COMPONENTS ... 6‘3 SECTION 7 PARTS AND SCHEMATICS 7.1 DRAWINGS ... 7'1 7.2 ADDENDA ... 1Λ 7.3 ORDERING PARTS ... 7'1

mehr