Ramsey Electronics COM 3 Communications Test Set
Hersteller:
Modell:
COM 3
Datum:
1987
Kategorie:
Gruppe:
Beschreibung:
Communications Service Monitor

Information

The COM 3 is a lightweight, compact service monitor for testing AM and FM transceivers. The internal battery, which is a standard feature of the COM 3 combined with the optional carrying case and low weight (13 lbs), make it ideal for field use. Utilizing specially designed micro powered oven circuits, warm -up time is minimal, providing maximum use of the battery. The frequency range is 100 KHz to 999.999 MHz in 500 Hz steps. Standard CTS tones as well as a 1 KHz tone can be generated. RF power is continuosly variable in five ranges from 0.1 ¡iv to 10,000 ¡j.v. The display is a seven digit LED type which will display frequencies generated or received, CTS off air, as well as being an audio and RF frequency Counter. Deviation and frequency error are displayed on a 20 segment LED bargraph, which is easily visible from across the shop. An internal RF relay switches transmitted power greater than 500 mW to a rear panel mounted BNC connector. This protects the COM 3 from accidental keying and allows easy connection of an antenna, power meter, or dummy load.

mehr

Bedienungsanleitung mit Schaltplan
Dokumenttyp:
Bedienungsanleitung mit Schaltplan
Seiten:
37
Größe:
9.35 Mbytes (9806215 Bytes)
Sprache:
english
Revision:
1.7
Dokument-ID:
Datum:
1987 01 01
Qualität:
Gescanntes Dokument, alles ist lesbar.
Upload Datum:
2017 02 04
MD5:
7400a59ce6edc31a90a0b6f39aa4615b
Downloads:
1084

Information

Section 1 - General Information 1.1 Introduction 1.2 Specifications 1.3 Options 1.4 Special Modifications Section 2 - Installation 2.1 Introduction 2.2 Unpacking and Inspection 2.3 Power Requirements 2.4 Enviromental Considerations Section 3 - Operation 3.1 Introduction 3.2 Front Panel Description 3.3 Initial Turn On 3.4 Generate RF 3.5 RF Output Level 3.6 FM Modulation 3.7 AM Modulation 3.8 CTS Tone Generation 3.9 1 KHz Internal Tone 3.10 External Source Input 3.11 Combining CTS and Internal/External Tone Sources 3.12 Offset+/Offset- 3.13 500 Hz Step 3.14 Storing/Recalling Test Setups 3.15 Spurious Signals 3.16 Leakage 3.17 Audio Count Off Air 3.18 Audio Count External 3.19 RF Count Section 4 - Typical Test Setups 4.1 Introduction 4.2 Frequency Counter : Off Air 4.3 Frequency Counter : Direct Connection 4.4 Frequency / Deviation Measurements 4.5 20 dB Quieting Measurement 4.6 12 dBSinad Measurement 5.1 General 5.2 512-1018 MHz Coarse Loop PLL 5.3 5-7 MHz Fine Loop PLL - 5.4 1024 MHz Offset PLL 5.5 Output Step Attenuator 5.6 4 MHz Reference Standard 5.7 FM Modulator 5.8 AM Modulator 5.9 1 KHz Source 5.10 Receiver 5.11 16 KHz Reference Generator 5.12 Frequency Error Detector 5.13 Audio Amp 5.14 + 30 Volt and -10 Volt Supplies 5.15 Transmit Protection Circuit 5.16 DC Supply and Battery 5.17 Membrane Switch 5.18 Microprocessor 5.19 Display Drivers 5.20 Audio Frequency Counter 5.21 RF Frequency Counter 5.22 CTS Tone Generation 5.23 Frequency Error/Deviation Display Section 6 - Documents,Figures Fig 3.1 Front panel layout Fig 4.1 Block diagram Schematic diagram Warranty Test data

mehr