Geräte Informationen:

Kikusui Electronics Corporation PMC18-3A Sonstiges
Hersteller:
Kikusui Electronics Corporation
Modell: PMC18-3A
Datum: 1994
Kategorie: Messgeräte
Gruppe: Sonstiges
Beschreibung: REGULATED DC POWER SUPPLY
Informationen:
                                    The PMC-A series Regulated DC Power supply is an automatic
constant voltage/constant current shift type. It employs a
series regulator system and delivers a stable output wish
low noise.
• The PMC-A series, which has two bright 3-l/2digit LED
display meters, displays the output voltage and the output
current or their settings.
» The potentiometers for the output voltage and current
setting are 10 turns wire wound type, allowing
high-resolution setting and stable output.
• The output switch is an electronic switch. It causes no
chattering or noise. It can be controlled from the panel or
from a remote place.
• The output voltage and current can be remote-controlled by
an external analog signal (voltage or Resistor). The PMC-A
series can be used as a system component of an automation
system with GPIB Interface such as KIKUSUI’s PIA 3200.
ThePMC-A series can be used in a wide application field from
use in a laboratory for experiment to that on a production
line for testing.

Folgende Anleitungen sind hier verfügbar:

Dokumenttyp: Bedienungsanleitung Kikusi-7065-Manual-Page-1-Picture
Seitenanzahl: 34
Dateigröße: 861.98 Kbytes (882669 Bytes)
Sprache: Englisch
Revision:
Dokument-ID/Nummer: Z1 -000-582 IA000791
Datum: 1994
Qualität: Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
MD5: 5314dd6f1a65979aa2b0b17a320f4798
Downloads: 640 seit dem 14 August 2015
Informationen:
SAFETY
SUMMARY ... 
I CHECK AT
UNPACKING ... 
ffl PACKING FOR
RE-SHIPMENT ... 
IE Chapter 1 GENERAL
DESCRIPTION ... 
1 Chapter 2 PRECAUTION AND PREPARATION FOR
USE ...  1
2.1 Inrush
Current ... 
1
2.2
Environment ... 
2
2.3 Type οΓ Load
 ... * ... 
3
Chapter 3 PANEL
DESCRIPTION ... 
4
3.1 Front
Panel ... * ... - ... 
4
3.2 Rear
Panel ... * ... 
6
Chapter 4 OPERATING
METHOD ... 
7
4.1 Basic
Operation ... *—·** ... 
7
4.1.1 Turning the POWER switch
on/off ...  7
4.1.2 Setting the output voltage or current,
and turning the output on/off
 ...  7
4.1.3 OVP trip voltage
setting ... * ... * ...  7
4.2 Applied
Operation ... '·-** ... 
8
4.2.1 Remote
sensing**···—— ... —* ... 8
4.2.2 Analog remote
control ... 8
4.2.3 Series operation and parallel
operation ... 12
4.2.4 Master/Slave controlled parallel
operation ... * ... 14
Chapter 5 MAINTENANCE AND
CALIBRATION ... * ...  15
5.1 Maintenance and Checking
 ... * ...  15
5.2
Calibration ... - ... * ... 
15
5.2.1
Preparation ... * ... 15
5.2.2 Test equipment
required ... * ... 16
5.2.3 Calibration setup
·■— ... * ... 16
5.2.4 Calibration procedure
 ... 17
Chapter 6
SPECIFICATIONS ... ····
19
6.1 Electrical Specifications
···■· ...  19
6.2
Dimensions ... 
21
6.3
Option ... 
21
Kikusi-7065-Manual-Page-1-Picture


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Captcha Image
Powered by Commentics