Wavetek - 184 - Generator
Hersteller:
Gerät:
184
Datum:
1980
Kategorie:
Gruppe:
Untergruppe:
Informationen
THE MODEL 184 Wavetek Model 184 the 5 MHz Sweep Generator is a precision
source of sine, triangle, square, positive pulse and
negative pulse waveforms plus dc voltage. Frequency of the
waveforms is manually and remotely variable from 100µHz to 5
MHz.
The Generator can repetitively sweep between two
individually set frequencies and at a particular sweep rate.
The amplitude of waveforms is variable from 20V p-p, open
circuit maximum, to —80 dB.
DC reference of the waveforms can be offset positively and
negatively.
The symmetry of the waveforms is continuously adjustable
from approximately 1:19 to 19:1. Varying symmetry provides
variable duty cycle pulses, sawtooth and asymmetrical sine
waveforms.
A voltage representing Generator frequency, a
fixed-amplitude pulse train of that frequency, and a voltage
ramp representing frequency sweep rate are provided as front
panel outputs.
2 Handbücher
Reparatur und Bedienungsanleitung
Dokumenttyp:
Reparatur und Bedienungsanleitung
Seitenanzahl:
52
Größe:
1,6 MB
Sprache:
englisch
Revision:
Dokument-ID:
Datum:
Februar 1980
Qualität:
Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
13. August 2018
MD5:
0bc85881-272d-20be-9947-e91dcbc07846
Informationen
1.1 THE model 184 1-1
1.2 SPECIFICATIONS...1-1
SECTION 2 INITIAL PREPARATION
2.1 UNPACKING INSPECTION...2-1
2.2 PREPARATION FOR USE...2-1
2.3 ELECTRICAL ACCEPTANCE CHECK...2-1
SECTION 3 OPERATION
3.1 CONTROLS AND CONNECTORS...3-1
3.2 OPERATION...3-4
3.2.1 Signal Termination . ...3-4
3.2.2 Continuous Operation... . 3-5
3.2.3 Trigger Mode...3-5
3.2.4 Triggering...3-6
3.2.5 GATED (or Tone Burst) Mode...3-6
3.2.6 SWEEP Mode...3-6
3.2.7 Voltage Control - VCG...3-6
SECTION 4 CIRCUIT DESCRIPTION
4.1 VOLTAGE CONTROL LED GEN ERATO ft...4-1
4.2 SWEEP Generator 4-2
SECTION 5 CALIBRATION
5.1 FACTORY REPAIR...5-1
5.2 REQUIRED TEST EQUIPMENT...5-1
5.3 REMOVING Generator COVER...5-1
5.4 CALIBRATION...5-1
SECTION 6 TROUBLESHOOTING
6.1 INTRODUCTION...6-1
6.2 CIRCUIT BOARD ACCESS...6-1
6.3 BASIC TECHNIQUES...6-1
6.4 TROUBLESHOOTING INDIVIDUAL COMPONENTS...6-1
6.5 TROUBLESHOOTING GUIDE...6-2
SECTION 7 PARTS AND SCHEMATICS
7.1 DRAWINGS...7-1
7.2 ORDERING PARTS...7-1
7.3 ADDENDA...7-1
Downloads:
718
Downloads letzter Monat:
10
Herunterladen
wavetek--184--service-user--ID11106.pdf
Reparaturanleitung
Dokumenttyp:
Reparaturanleitung
Seitenanzahl:
13
Größe:
1,5 MB
Sprache:
englisch
Revision:
Dokument-ID:
Datum:
Januar 1975
Qualität:
Gescanntes Dokument, schwer zu lesen, teilweise nicht zu lesen.
Upload Datum:
30. Dezember 2020
MD5:
08019804-2997-8faf-1424-1e7b11cd5671
Informationen
Calibration Procedure
Downloads:
927
Downloads letzter Monat:
6
Herunterladen
wavetek--184--service--ID13489.pdf