Simpson - 260 Series 7 - Analog Multimeter
Hersteller:
Gerät:
260 Series 7
Datum:
1981
Kategorie:
Gruppe:
Untergruppe:
Informationen
The Simpson Volt-Ohm-Milliammeters 260 Series 7 and Series
7M (hereafter referred to as the 260 or as the Instrument),
are identical instruments electrically and mechanically,
except that the Series 7M is equipped with a mirrored dial
to eliminate parallax (Figures 1-1 and 1-2). The 260 Series
7 is a rugged, accurate, compact, easy-to-use instrument.
The Instrument can be used to make accurate measurements of
AC and DC voltage, direct current, resistance, decibels, and
Output Voltage. The Output Voltage function is used for
measuring the AC component of a mixture of AC and DC
voltage. This occurs primarily in amplifier circuits.
1.1.2 New Features in the 260-7 and 7M are:
• New connectors between the Instrument and the test leads
which eliminates a shock hazard in the event a connector is
inadvertently pulled out of the Instrument jack.
• A high energy fuse F2 which is now in the BATTERY AND FUSE
COMPARTMENT, and accessible without removing the Instrument
case.
• An OFF/TRANSIT position which has been added to the
function switch to protect the meter movement during
transit. (This, position shunts the meter movement and opens
the internal connections to the COMMON and + jacks.)
• A test lead set with molded elbow prods at one end for
connection to the front panel input terminals and test
probes at the other end. The test probes have a non-slip
grip surface and a barrier to maintain the spacing between
the user’s fingers and the probe tip. Threaded shoulders at
the probe tip accept screw-on alligator clips (supplied) or
an accessory AC or DC 5000 volt range extending probes.
1 Handbuch
Reparatur und Bedienungsanleitung
Dokumenttyp:
Reparatur und Bedienungsanleitung
Seitenanzahl:
60
Größe:
1,7 MB
Sprache:
englisch
Revision:
third
Dokument-ID:
6-111452
Datum:
Qualität:
Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
22. November 2014
MD5:
bf9c1826-bf70-b401-a0f8-7f4040466e56
Informationen
SECTION I
Introduction
....................................................................................
1-1
1.1 General
........................................................................
1-1
1.2 Description
.................................................................
1-2
1.3 Internal
Batteries........................................................
1-3
1.4 Printed
Circuit.............................................................
1-3
1.5 Phenolic Case
............................................................. 1-3
1.6 Adjust-A-Vue
Handle............................................... 1-4
1.7 Test
Leads....................................................................
1-4
1.8 Technical Data
.......................................................... 1-5
1.9 Definition of
Accuracy............................................... 1-7
1.10 Safety Considerations
............................................... 1-7
SECTION II
Installation
......................................................................................
2-1
2.1 General
.........................................................................
2-1
2.2 Unpacking and
Inspection........................................ 2-1
2.3 Warranty
......................................................................
2-1
2.4 Shipping
......................................................................
2-2
2.5 Power Source
Requirements................................... 2-2
2.6 Operating
Position......................................................
2-2
SECTION ΙΠ
Controls, Jacks, and Indicators
................................................. 3-1
3.1 General
........................................................................
3-1
3.2 Front Panel
Description............................................. 3-1
SECTION IV
Operation
.........................................................................................
4-1
4.1 General
........................................................................
4-1
4.2 Safety
Precautions......................................................
4-1
4.3 Polarity
Reversing......................................................
4-3
4.4 Measurement of Unknown Voltage or Current . . 4-4
4.5 Test
Leads....................................................................
4-4
4.6 DC Voltage Measurement 0-250 mV Range .... '4-4
4.7 DC Voltage Measurement 0-1V Range..................4-5
4.8 DC Voltage Measurement
0-2.5 Through 0-500V Range...................................4-7
4.9 DC Voltage Measurement 0-1000V Range............4-8
4.10 AC Voltage Measurement
0-2.5 Through 0-500V
Range...................................4-10
4.11 AC Voltage Measurement 0-1000V Range............4-12
4.12 Output Voltage
Measurement...................................4-13
4.13 Decibel Measurements (—20 to +50 dB)..............4-15
4.14 Direct Current
Measurement.....................................4-18
4.15 Direct Current Measurement 0-50/; A Range .... 4-18
4.16 Direct Current Measurement
0-1 mA Through 0-500 mA Range..........................4-20
4.17 Direct Current Measurement 0-10A Range............4-21
4.18 Resistance Measurements
..........................................4-22
4.19 Measuring Resistance
.................................................4-22
4.20 Resistance Measurement of Semiconductors .... 4-24
SECTION V
Operator Servicing
..........................................................................5-1
5.1 General
..........................................................................5-1
5.2 Inspection
......................................................................5-1
5.3 Battery
Replacement...................................................5-1
5.4 Fuse
Replacement........................................................5-2
5.5 Test Lead
Inspection...................................................5-4
5.6 Care
.................................................................................5-4
SECTION VI
Servicing
Instructions......................................................................6-1
6.1 General
..........................................................................6-1
6.2 Removing the Instrument
Case................................6-1
6.3 Replacement Parts and Schematic Diagram...........6-1
Downloads:
3308