BK Precision 889B LCR Meter
Producent:
Model:
889B
Data:
2009
Kategoria:
Grupa:
Opis:
Bench LCR/ESR Meterwith ComponentTester

Informacja

The B&K Precision Corp. 889B Synthesized In-Circuit LCR/ESR Meter is a high accuracy test instrument used for measuring inductors, capacitors and resistors with a basic accuracy of 0.1%. Also, with the built-in functions of DC/AC Voltage/Current measurements and Diode/Audible Continuity checks, the 889B can not only help engineers and students to understand the characteristics of electronics components but also being an essential tool on any service bench. The 889B is defaulted to auto ranging. However, it can be set to auto or manual ranging by pressing the Range Hold key. When LCR measurement mode is selected, one of the test frequencies, 100 Hz, 120 Hz, 1 KHz, 10 KHz, 100 KHz or 200 KHz, may be selected on all applicable ranges. One of the test voltages, 50mVrms, 0.25 Vrms, 1 Vrms or 1 VDC (DCR only), may also be selected on all applicable ranges. The dual display feature permits simultaneous measurements. When DC/AC voltage/current measurement mode or the Diode/Audible Continuity Check mode is selected, only the secondary display will be used to show the result of the measurement. The highly versatile 889B can perform virtually all the functions of most bench type LCR bridges. With a basic accuracy of 0.1%, this economical LCR Meter may be adequately substituted for a more expensive LCR bridge in many situations. Also, with the basic accuracy of 0.4% in voltage and current measurements, the 889B performs the functions of a general purpose Digital Multi-Meter and can be used to replace the DMM on a service bench. The 889B has applications in electronic engineering labs, production facilities, service shops, and schools. It can be used to check ESR values of capacitors, sort and/or select components, measure unmarked and unknown components, and measure capacitance, inductance, or resistance of cables, switches, circuit board foils, etc. The key features are as following: 1. Voltage Measurements: • AC : True RMS, up to 600Vrms @ 40 ~ 1K Hz • DC : up to 600V • Input Impedance : 1M-Ohm 2. Current Measurements: • AC : True RMS, up to 2Arms @ 40 ~ 1K Hz • DC : up to 2A • Current Shunt : 0.1 Ohm @ > 20mA; 10 Ohm @ < 20mA 3. Diode/Audible Continuity Checks: • Open Circuit Voltage: 5Vdc • Short Circuit Current: 2.5mA • Beep On: < 25 Q • Beep Off: > 50 Q 4. LCR Measurements: • Test conditions Frequency : 100Hz/120Hz/1KHz/10KHz/100KHz/200KHz Level : 1Vrms / 0.25Vrms / 50mVrms / 1VDC (DCR only) • Measurement Parameters : Z, Ls, Lp, Cs, Cp, DCR, ESR, D, Q and 0 • Basic Accuracy : 0.1% • Dual Liquid Crystal Display • Auto Range or Range Hold • USB Interface Communication • Open/Short Calibration • Primary Parameters Display: Z : AC Impedance DCR : DC Resistance Ls : Serial Inductance Lp : Parallel Inductance Cs : Serial Capacitance Cp : Parallel Capacitance • Second Parameter Display: 0 : Phase Angle ESR : Equivalence Serial Resistance D : Dissipation Factor Q : Quality Factor • Combinations of Display: Serial Mode : Z -0, Cs - D, Cs - Q, Cs - ESR, Ls - D, Ls - Q, Ls - ESR Parallel Mode : Cp - D, Cp - Q, Lp - D, Lp - Q

pokaż więcej

Instrukcja obsługi
Typ ręczny:
Instrukcja obsługi
Strony:
35
Rozmiar:
454.56 Kbytes (465470 Bytes)
Język:
english
Rewizja:
Ręczny ID:
481-528-9-001
Data:
2009 01 01
Jakość:
Skanowany dokument, wszystko czytelne.
Data przesłania:
2017 01 25
MD5:
feee51fe8ba0701bf40c182bbb0ba64b
Pobrane:
488

Informacja

1. INTRODUCTION ... 3 1.1 General ... 3 1.2 Impedance Parameters ... 4 1.3 Specification ... 5 1.4 Accessories ... 13 2. OPERATION ... 14 2.1 Physical Description ... 14 2.2 Making Measurement ... 15 2.2.1 Open and Short Calibration ... 15 2.2.2 Relative Mode ... 15 2.2.3 Range Hold ... 15 2.2.4 DC Resistance Measurement ... 16 2.2.5 AC Impedance Measurement ... 16 2.2.6 Capacitance Measurement ... 16 2.2.7 Inductance Measurement ... 16 3. OPERATION MODES ... 17 3.1 Remote Mode Command Syntax ... 20 3.2 Remote Mode Commands ... 20 4. APPLICATION ... 26 4.1 Test Leads Connection ... 26 4.2 Open/Short Compensation ... 28 4.3 Selecting the Series or Parallel Mode ... 29 5. limited one-year warranty and service information ... 31 6. SAFETY PRECAUTION ... 33

pokaż więcej