Electronic Navigation Industries 5100L Amplifier
Manufacturer:
No picture available!
Maybe you can upload a photo for the
Electronic Navigation Industries 5100L ?
If you have any other manuals for the
Electronic Navigation Industries 5100L you can upload the files here .
Model:
5100L
Date:
1995
Category:
Group:
Description:
BROADBAND POWER AMPLIFIER
Information
The Model 5100L is a general purpose broadband Amplifier
capable of more than 100 watts of linear power output when
driven by any laboratory signal or sweep generator from 1,5
to 400 MHz.
An ultra linear Class A design, the 5100L will "boost" the
output of any signal source by a fiat 50 dB (±1.5 dB) and
provide its full forward output power into any load
impedance (from an open to a short circuit). Its output is a
faithful reproduction of the input waveform for AM, FMr SSB,
CATV; pulse and other complex modulations. Although
specified only over the 1.5 to 400 MHz frequency range, full
power output is typically available from 1 to 410 MHz.
The use of stud mounted UHF transistors on microstrip
circuit boards makes the 5100L both reliable and easy to
service. An integral Power Supply and cooling system permits
operation over a wide band of temperature and AC line
conditions.
Manual type:
Service and User Manual
Pages:
80
Size:
2.04 Mbytes (2138067 Bytes)
Language:
english
Revision:
D1
Manual ID:
5100L-TM-01
Date:
Quality:
Scanned document, reading partly badly, partly not readable.
Upload date:
2016 01 25
MD5:
c071971286e106cdf6dc566a58bb165f
Downloads:
454
Information
Chapter 1 Safety
1.1
Labels ... 1-1
1.1.1 Important Operating or Maintenance
Cautions ... 1-1
1.1.3
Service ... 1-2
1.1.4 Name
Plate ... 1-2
Chapter 2 System Installation
2.1 Initial
inspection ... 2-1
2.1.1 Mechanical
Inspection ... 2-1
2.1.2 Claim for
Damage ... 2-1
2.1.3 Packaging for
Reshipment ... 2-1
2.2 Preparation for
Use ... 2-2
2.1.1 Power
Requirements ... 2-2
2.2.2 Power Cable Ground
Protection ... 2-2
2.2.3
Cooling ... 2-2
2.3 Rack
Mounting ... 2-3
Chapter 3 5100L Operation
3.1 Functional
Description ... , ... 3-1
3.2 Controls, indicators and
Connectors ... 3-2
3.2.1 Power
Switch ... 3-2
3.2.2 Input
Connector ... 3-2
3.3.3 Output
Connector ... 3-2
3.2.4
Fuse ... 3-2
3.2.5 Line
Cord ... 3-2
3.3 Operating
Procedures ... 3-3
3.4
Precautions ... 3-4
Chapter 4 Technical Description
4.1 System
Overview ... 4-1
4.2 Block Diagram
Description ... 4-2
4.2.1 Preamplifier
Module ... 4-2
4.2.2 Power Amplifier
Module ... 4-3
4.2.3 Output Combiner
Module ... 4-3
4.2.4 Power
Distribution ... 4-3
Chapter 5 Maintenance and Calibration
5.1 Recommended Test
Equipment ... ,.5-1
5.2 Performance
Tests ... 5-2
Calibration of Set
Up ... 5-2
Measurement
Procedure ... 5-3
5.2.2 RF Power Output
Test ... 5-3
Measurement
Procedure ... 5-3
5.2.3 RF Power Distortion
Test ... 5-4
Measurement
Procedure ... 5-4
5.3 Locating a Faulty RF
Module ... 5-5
5.3.1 Isolating the Amplifier
Problem ... 5-5
Eight Way Combiner
Test ... 5-5
RF Power Amplifier Module
Test ... 5-6
Bias Voltage
Check ... 5-6
Low Power Sweep Test Set Up ... 5-7
Measurement Procedure ... 5-8
5.3.2 Preamplifier
Module ... 5-8
5.4 DC Power
Supply ... 5-9
Chapter 5 Maintenance and Calibration (Continued)
5.4.1 Test
Procedure ... 5-9
5.5 Disassembly
Procedures ... 5-10
5.5.1 Tools
Required ...
5-10
5.5.2 Removal of
Cover ... 5-10
5.5.3 Preamplifier
Assembly ... 5-10
5.5.4 Eight Way Output Combiner
Assembly ... 5-10
5.5.5 Power Amplifier Heatsink
Assemblies ... 5-11
5.5.6 Power Amplifier
Module ... 5-11
5.5.7 Power Amplifier Regulator
Board ... 5-11
5.5.8 Power Amplifier Power
Supply ... 5-11
5.5.9 Power Amplifier/Preamplifier Power
Supply ... 5-12
Chapter 4 Troubleshooting
Troubleshooting Guide ... I ... ; ... 4-2
Appendix A 5100L
Specifications ... A~1
Appendix B Schematics and Materials
This section contains the following board layouts, related
schematics and parts list.
Schematics
Schematic
Diagram ... 5100L-SCH-01
Power
Distribution ... 5100L-2431
Parts
List ... 5100L-1431