Ailtech 7320 Ander
Fabrikant:
Model:
7320
Datum:
1978
Categorie:
Groep:
Omschrijving:
System Noise Monitors

Informatie

The System Noise Monitors described in this Instruction Manual /7310 and(7320) are functionally identical. Each provides a readout of the Noise Figure of a unit under test (UUT) when connected in a valid measurement setup. The minimum test setup consists of a SNM, the UUT, and a solid state noise source of the Ailtech 7600 series. The 7310 and 7320 have optional meter scales which provide an Operating Noise Temperature readout in lieu of Noise Figure. The 7310 and 7320 SNM’s are referred to as analog units because the readout is by a meter with two ranges. Range selection is made by means of a front panel switch. Ailtech also manufactures the 7360 and 7370 which indicate Noise Figure by means of a three-digit LED display and are generally referred to as digital units. The 7310 is 7½ inches wide and is intended for bench-top use while the 7320 is approximately 17 inches wide and is intended for rack mounting. The optional Rack Mount Angle Brackets (Option 11) must be attached for mounting in a standard 19 inch rack.

toon meer

Service-en gebruikershandleiding
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
48
Grootte:
1.35 Mbytes (1420405 Bytes)
Taal:
english
Herziening:
B
Handleidingen-ID:
Datum:
Kwaliteit:
Gescand document alle leesbaar.
Upload datum:
2013 03 16
MD5:
0b4f0635a907f9ba1ca88e1ddd578fe3
Downloads:
1392

Informatie

Chapter I-General Information 1-1. Introduction 1-1 1-3. General Description 1-1 1-7. Safety Precautions 1-1 1-10. Technical Specifications 1-1 1-12. Functional Description 1-5 1-13. General 1-5 1-15. The Noise Monitor in a Typical Application 1-5 1-17. Auxiliary Outputs 1-6 1-19. Options 1-6 1-21. Accessories 1-7 1-22. Noise Generators 1-7 1-23. Precision Attenuation 1-9 1-24. Test Equipment 1-10 Chapter 11-Installation 2-1. Introduction 2-1 2-3. Unpacking, Inspection and Damage Claims 2-1 2-5. Ancillary Items 2-1 2-7. Rack Mounting 2-1 2-9. Preparation for Use 2-1 2-11. Initial Checkout 2-2 2-14. General 2-2 2-16. Checkout Procedures 2-2 Chapter Ill-Operating Instructions 3-1. General 3-1 3-3. Description of Operating Controls, Indicators and Connectors 3-1 3-5. Set-up Procedures 3-1 3-8. Interconnections 3-1 3-17. Excess Noise Ratio Setting 3-5 3-21. Establishing the Correct Signal Levels 3-5 3-27. Operation 3-7 3-31. Use of Auxiliary Outputs 3-9 3-33. Signal Monitor, Jl, Pin 4 3-9 3-35. External Meter, Jl, Pins 6 and 7 3-9 3-37. Recorder Output, Jl, Pin 8 3-10 3-39. Manual Noise Figure (Temperature) Measurements 3-10 Chapter IV-Theory of Operation 4-1. Introduction 4-1 4-3. General Theory 4-1 4-4. Noise Figure Theory 4-1 4-6. Noise Figure Measurement 4-2 4-8. Operating Noise Figure and Temperature Measurement 4-4 4-11. Functional Description (Automatic Noise Measurement) 4-5 4-15. Circuit Descriptions 4-8 4-17. IF Amplifier 4-9 4-22. Square Law Detector ... — ... 4-9 4-24. Variable Gain Amplifier 4-9 4-25. Synchronous Integrator and Meter Amplifier 4-9 4-26. AGC Amplifier 4-9 4-31. Timing Signal Generator 4-10 4-39. Power Supply Board 4-13 4-41. +12 Volt Regulator 4-14 4-42. -12 Volt Regulator 4-14 4-43. +28 Volt Noise Source Supply 4-14 Chapter V-Maintenance and Adjustments 5-1. General 5-1 5-3. Performance Verification 5-1 5-6. Minimum Operating Level 5-1 5-7. Noise Generator Power 5-2 5-8. Accuracy 5-2 5-10. Checks and Adjustments 5-3 5-13. Power supply Adjustments 5-5 5-14. IF Adjustments 5-5 , 5-16. Preliminary 5-5 5-17. Procedure 5-6 5-18. Meter Adjustments 5-6 5-20. Auxiliary Output Adjustments 5-6 5-22. Signal Monitor 5-6 5-23. Recorder Output 5-7 5-24. Troubleshooting 5-7 5-26. General Information 5-7 5-27. Tools 5-7 5-28. Transistors 5-7 5-29. Integrated Circuits 5-8 5-30. Logic Family 5-8 5-31. Logic Circuits 5-8 5-32. Analog Gates 5-8 5-33. Operational Amplifiers 5-8 5-34. Printed Circuit Boards 5-8 5-37. Printed Circuit Board Connectors 5-8 5-38. Front Panel Lamps 5-13 5-39. ENR Thumbwheel Switch 5-14 5-40. Troubleshooting Procedures 5-14 5-44. Factory Service 5-14 Chapter Vi-Spare Parts 6-1. General 6-1 6-2. Recommended Spare Parts 6-1 6-3. Replaceable Spare Parts 6-1

toon meer

Service-en gebruikershandleiding
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
102
Grootte:
3.50 Mbytes (3669192 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
Datum:
Kwaliteit:
Gescand document alle leesbaar.
Upload datum:
2014 04 22
MD5:
cba1429e6844dfbef00accb0ffe62959
Downloads:
1407

Informatie

This Instruction Manual is for the Ailtech 7310 and Ailtech 7320 System Noise Monitors (SNM), figure 1-1, and contains physical and functional descriptions, installation and inspection procedures, operating and maintenance instructions, and a parts list for each model. All schematics, electrical and assembly drawings are included, as are appendices for the available optional features. Unless otherwise stated, the information provided herein applies to both models.

toon meer