|Gould K100-D Logic Analyzer|
|Beschrijving:||Digital Logic Analyzer|
The Model K100-D Logic Analyzer was designed to provide the utmost in performance and versatility for the digital designer and troubleshooter; i.e., it can be considered to be a true benchmark tool. It serves as both a time domain (data recorded asynchronously), and a data domain analysis tool (data recorded synchronously). The unit accepts up to 16 logic signals through its active input probes, and stores these discriminated signals in its 1024 word memory, at sample rates to 100 MHz. The Model K100-D has comprehensive recording and display analysis capabilities that enable the user to perform complex timing and state analysis of his digital systems. The unit has three distinct features that make it a useful tool for logic troubleshooting. First, the signals from the user's system are input via specially designed hybrid active probes. The input impedance of each probe is 1 MΩ , 5 pF. The probes are individual to allow spanning to physically separated points in the system, and also to provide for convenient connection at the PC board level. Signal conditioning, or threshold detection, and buffering of a particular signal is provided at a point as close as possible to the user's circuitry. The probe tip, with its accessories, allows convenient connection to a system. The probes detect logic spikes or glitches down to 5 ns regardless of clock rate used. Second, the instrument can clock at rates to 100 MHz allowing timing measurements on up to 16 signals, with a 10 ns time resolution. A relatively long memory, 1024 words, allows precise timing measurements over longer intervals of time. The performance of the active probes complement this high-speed recording capability. Third, the instrument uses a microprocessor linked to a front keyboard for instrument control. Comprehensive display prompting is used to make it easy to set up the unit for desired recording and display formats.
Deze handboeken zijn beschikbaar voor de bovengenoemde apparatuur:
|Gould -- K100-D -- Service-en gebruikershandleiding|
|Handleidingen Type:||Service-en gebruikershandleiding|
|Maat:||10.20 Mbytes (10698838 Bytes)|
|Datum:||15 februari 1980|
|Kwaliteit:||Gescande document, lezen deels slecht, deels niet leesbaar.|
|Upload datum:||11 maart 2013|
|Downloads:||182 Sinds 11 maart 2013|
General Information 1.1 Certification 1 1.2 Warranty 1 1.3 Description 1 1.4 Specifications 3 Installation 2.1 Introduction 5 2.2 Unpacking and Inspection 5 2.3 Storage and Shipment 5 2.4 Power Connection 5 2.5 Preparation for Use 5 2.6 Initial Warm-up 6 Operation 3.1 Introduction 8 3.2 Front Panel Controls and Inputs 8 3.3 Rear Panel Inputs and Outputs 20 3.4 Set-up Procedure and 21 Operation Principles of Operation 4.1 Introduction 26 4.2 Basic General Description 26 4.3 Detailed Description 29 4.4 Front End 41 4.5 Record Control 48 4.6 Record Memory 58 4.7 Threshold 64 4.8 Front Panel and Keyboard 67 4.9 Probes 67 4.10 Regulator 69 4.11 CRT Display 70 Calibration Procedures 5.1 Recalibration of Internal Circuits 74 5.2 Required Test Equipment 74 5.3 Calibration of Raster Scan Display 74 5.4 Power Supply Adjustments 77 5.5 Threshold Adjustments 77 5.6 Record Memory Adjustments 78 5.7 Special Precautions 80 Maintenance 6.1 Introduction 81 6.2 Diagnostic Routine and Indications 81 6.3 Required Test Equipment 87 6.4 Diagnostic and Troubleshooting Procedures 87
|Start gratis downloaden|
No comments yet. Be the first!