Tektronix TLA7PG2 TV patroon generator
Fabrikant:
Model:
TLA7PG2
Datum:
Categorie:
Groep:
Omschrijving:
Pattern Generator and Probes

Informatie

The TLA7PG2 Pattern Generator is a 64-channel, programmable pattern Generator module with sequential control that plugs into the TLA700 series mainframes, and is intended for use as an integral component of the Tektronix Logic Analyzer Family series of products. The pattern Generator module provides multichannel signals for use in applications, such as simulation of missing system elements, erroneous signals for stress testing, or extended analysis for simulating a device under test. You can put circuits in a desired state and operate the pattern Generator at full speed or single step it through a series of states. The TLA7PG2 Pattern Generator can also generate infrequently encountered test conditions to test a hardware design or Software program for robustness. The TLA7PG2 Pattern Generator supports the following probes: P6470 TTL/CMOS P6471 ECL P6472 PECL/LVPECL P6473 LVDS P6474 LVCMOS P6475 Variable You can have up to four probes on each pattern Generator. Following are some of the key features of the TLA7PG2 Pattern Generator: Provides up to 64 channels Offers a Jump If condition for all data blocks (maximum of 4000) up to clock rates of 268 MHz The TLA7PG2 Pattern Generator can fully test circuits at real clock speeds, without having to use improvised setups.

toon meer

Servicehandboek
Handleidingen type:
Servicehandboek
Pagina’s:
252
Grootte:
1.80 Mbytes (1886972 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
071-0714-01
Datum:
Kwaliteit:
Elektronisch document, geen scan, zeer goed leesbaar.
Upload datum:
2017 12 26
MD5:
4c7bc52a3e8a9200153473ab866ecddd
Downloads:
580

Informatie

This is the service manual for the TLA7PG2 Pattern Generator. The manual contains information needed to service the pattern Generator to the module level. The following lists contains a brief description of each manual section. The Specifications contains a description and a list of the characteristics of the pattern Generator and pattern Generator probes. The Operating Information includes general information and operating instructions at the level needed to safely power on and service the pattern generator. The Theory of Operation contains circuit descriptions that support general service to the module level. The Performance Verification contains procedures to verify the functional operation of the pattern Generator and modules as well as procedures to verify the performance to advertised specifications. The Adjustment Procedures normally lists procedures to adjust the instrument to meet advertised specifications. At this printing, there are no adjustment procedures required for the pattern Generator module. The Maintenance contains information and procedures for performing preventive and corrective maintenance of the pattern Generator module. These instructions include cleaning and fault isolation to the module. The Options contains information about options and Accessories that are available for the instrument. The Replaceable Electrical Parts contains a statement referring you to the Mechanical Parts List, where both electrical and mechanical parts are listed. The Diagrams contains block diagrams and cabling diagrams that are useful in isolating failed components. The Replaceable Mechanical Parts includes a table of all replaceable parts, their descriptions, and their Tektronix part numbers.

toon meer

Gebruikershandleiding
Handleidingen type:
Gebruikershandleiding
Pagina’s:
65
Grootte:
363.76 Kbytes (372488 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
071-1017-01
Datum:
Kwaliteit:
Elektronisch document, geen scan, zeer goed leesbaar.
Upload datum:
2019 09 23
MD5:
c5c7de9c89e846f41c1d04e2f51fa1f4
Downloads:
1712

Informatie

This document supports Tektronix Logic Analyzer Family Software Version 4.1 and Tektronix Pattern Generator Software Version 1.3 and above. General Safety Summary ... . Service Safety Summary ... . Related Documentation ... . Contacting Tektronix ... . Product Description ... . Probe Lead Sets and Cables ... . Connecting the Standard Probes ... . Connecting the P6475 Probe ... . Probe Connectors and Signal Names ... . Probe Overview ... . Probe Dimensions ... . P6475 Installation Requirements ... . Input/Output Circuits ... . Timing Diagrams ... . Specifications ... . Functional Check ... . Inspection and Cleaning ... . Static Discharge Information ... . Configuring Probes ... . Repackaging ... .

toon meer