JBL 6290 Versterker
Fabrikant:
Model:
6290
Datum:
1988
Categorie:
Groep:
Omschrijving:
Power Amplifier

Informatie

The JBL Model 6290 power Amplifier has been designed to meet the most critical professional sound requirements. It Is rugged and road-worthy, conservatively rated, and can handle reactive loads with ease. The engineering design approach stresses the optimization of each stage, allowing high slew rate and relatively low loop gain. Overall feedback has been held to a minimum and is employed only to stabilize the gain and the operating point. This design approach results In an Amplifier with excellent performance under the most demanding dynamic input and load conditions. As evidence of the stress on dynamic rather than static or steady-state distortion mechanisms, transient Intermodulation distortion measures less than 0.03$ by the DIM 100 test. (Leinonen, Otala, and Curl, "A Method for Measuring Transient Intermodulation Distortion (TIM)”, JournaI of the Audio Engineering Society, Vol. 25, No. 4, April, 1977, pp. 170-177.) This JBL Amplifier uses multiple 200-watt output devices in complementary configuration for high reliability and low distortion. At rated power Into 8 ohms, these output devices are operated at less than 25% of their rated power dissipation. The benefit Is high reliability and long component life. Reliable operation Is ensured through the following protection modes: current Is limited under Improper load or drive conditions; output relays with front panel Indicators protect the loudspeaker under conditions of DC offset or excessive low-frequency transients. The relays also provide power-up, power—down, and "brown out’1 muting to protect loudspeakers from AC power transients. Clip Indicators allow for system optimization. The JBL Amplifier may be operated In the normal stereo mode, dual mono mode, or bridged mono mode. These modes are switch selectable on the rear panel. Active differential Input circuitry offers the benefits of balanced operation without the use of Input transformers. Input connections may be made via 3-pln XL-type connector, three-conductor (TRS) 6.3 mm (1/4 In.) phone jack, or barrier strip. The barrier strip has separate terminals for audio ground and chassis ground. The rack ears and heatsink of the Amplifier are made of high grade aluminum extrusions; the chassis Is fabricated of heavy gauge steel. All Internal Components are easily accessible through removal of top and bottom panels. Front panel graphic details are Incorporated on the rear-side of a polycarbonate laminate which is virtually Indestructible.

toon meer

Service-en gebruikershandleiding
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
30
Grootte:
3.07 Mbytes (3220037 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
Datum:
1988 01 01
Kwaliteit:
Gescand document alle leesbaar.
Upload datum:
2017 10 29
MD5:
edf2136941c801cfc6108848e3b215fb
Downloads:
716

Informatie

SECTION I. INTRODUCTION 1-1 1.1 SPECIFICATIONS 1-2 SECTION II. INSPECTION AND INSTALLATION I 1-1 2.1 UNPACKING AND INSPECTION 11-1 2.2 ENVIRONMENTAL CONSIDERATIONS 11-1 2.3 AC POWER 11-1 2.4 AMPLIFIER MODE SWITCH 11-2 2.5 EXTERNAL CONNECTIONS 11-3 2.5.1 INPUT CONNECTIONS, GENERAL 11-3 2.5.2 INPUT CONNECTION, DUAL MONO MODE 11-3 2.5.3 INPUT CONNECTION, BRIDGED MONO MODE 11-3 2.5.4 FIVE-WAY BINDING POST OUTPUT CONNECTORS 11-4 2.5.5 ABOUT OUTPUT POLARITY AND BRIDGED MONO 11-4 CONNECTION 2.6 INPUT IMPEDANCE AND TERMINATION 11-4 2.7 APPROPRIATELY RATED LOADS 11-6 2.7.1 IT IS THE USER’S RESPONSIBILITY TO AVOID 11-6 OVERPOWER ING 2.7.2 MORE ABOUT LOUDSPEAKER POWER RATINGS 11-6 2.7.3 SOMETIMES A LARGER Amplifier CAN BE SAFER 11-7 2.7.4 REMEMBER THE DIVIDING NETWORK (CROSSOVER) 11-8 2.8 SPEAKER CABLES I 1-8 2.8.1 TYPE OF WlRE I I-8 2.8.2 DAMP ING FACTOR I I-8 2.8.3 CALCULATING LOSSES IN Speaker CABLE I I-9 2.9 GROUNDING 11-10 2.10 SECURITY COVERS 11-10 FIGURE 2-1 BALANCED INPUT CONNECTIONS 11-11 FIGURE 2-2 UNBALANCED INPUT CONNECTIONS 11-11 FIGURE 2-3 BARRIER STRIP CONNECTIONS 11-12 FIGURE 2-4 USE OF FIVE-WAY BINDING POSTS 11-13 FIGURE 2-5 OUTPUT CONNECTIONS TO TWO CHANNEL 11-13 Speaker SYSTEM FIGURE 2-6 BRIDGED OUTPUT CONNECTION TO MONAURAL 11-13 Speaker SYSTEM SECTION III. OPERATING INSTRUCTIONS I I 1-1 3.1 GENERAL I I 1-1 3.2 TURN ON AND SYSTEM CHECK MI-1 3.2.1 A NOTE ON Amplifier COOLING 111-1 3.3 CLIP INDICATORS II 1-1 3.3.1 ABOUT SENSITIVITY RATINGS 111-2 SECTION IV. THEORY OF OPERATION IV-1 4.1 INPUT DIFFERENTIAL AMPLIFIER IV-1 4.2 MODE SWITCH IV-1 4.3 POWER AMPLIFIER IV-1 4.4 RELAY DRIVER/OUTPUT DC DETECTOR IV-2 4.5 CLIP CIRCUIT IV-3 4.6 POWER SUPPLY IV-3 SECTION V. MAINTENANCE V-1 5.1 GENERAL V-1 5.2 REPAIRS AND WARRANTY V-1 SECTION V I. SCHEMATIC DIAGRAM

toon meer