Nelson-Ross Electronics Inc. PSA 012 Spectrum analyzer
Fabrikant:
Geen foto beschikbaar!
Misschien kan je een foto uploaden voor de
Nelson-Ross Electronics Inc. PSA 012 ?
Als je nog andere handleidingen hebt voor de
Nelson-Ross Electronics Inc. PSA 012 kun je hier de bestanden uploaden .
Model:
PSA 012
Datum:
Categorie:
Groep:
Omschrijving:
Plug-In Spectrum Analyzer
Informatie
These Analyzers are designed Co provide coverage of three
frequency ranges; 10 cps to 20 kc, 35 cps to 100 fcc, and
150 cps to 500kc. models 011, 012 and 013 are provided with
calibrated Center Frequency and Dispersion dials, while
models 001, 002 and 003 are uncalibrated.
These units are designed so that they may be conveniently
plugged into any Oscilloscope which accepts the Tektronix
letter series plug»ins. By simply installing one of these
Plug-In units, the Oscilloscope becomes a complete Spectrum
Analyzer. In use, the sawtooth output of the Oscilloscope is
utilized to provide a signal for sweeping the Spectrum
Analyzer Oscillator. Ail voltages for Spectrum Analyzer
operation are obtained automatically when the Analyzer is
plugged into the Oscilloscope.
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
63
Grootte:
2.16 Mbytes (2269887 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
Datum:
Kwaliteit:
Gescande document, lezen deels slecht, deels niet leesbaar.
Upload datum:
2017 08 19
MD5:
f89efc8be80ec91469fabb964436fc4b
Downloads:
2030
Informatie
This manual provides Operating Instructions, theory of
operation, Technical Characteristics, läintenance, and
Trouble Shooting Procedures for lîelson-itoss Plug-In Low
Frequency Spectrum Analyzers Models 001, Oil, 002, 012, 003,
013.
WARRANTY
SECTION I CHARACTERISTICS 1-1
Scope 1-1
General Information 1-2
SECTION 2 OPERATING INSTRUCTIONS 2-1
Inspection and Installation 2-1
Initial Adjustments 2-1
LF CAL Adjustment 2-2
Mixer Balance Adjustment 2-3
Control Function and Operation 2-5
Mode Switch 2-6
Center Frequency 2-6
Dispersion 2-6
Resolution 2-6
Gain Controls 2-8
Video Filter 2-9
Calibration 2-10
Application 2-11
Distortion Analysis 2-11
Intermodulation Distortion Percentage 2-11
Transducer Distortion Analysis 2-12
Environmental Noise 2-12
Machinery Vibration Analysis 2-12
Vibration Testing 2-13
Frequency Response 2-13
SECTION 3 CIRCUIT DESCRIPTION 3-1
General 3-1
Block Diagram Description 3-1
Detailed Circuit Description 3-2
Input Attenuator 3-2
Balanced Mixer 3-2
Range Attenuator 3-3
Crystal Filter 3-3
IF Amplifier 3-4
Log Circuitry 3-4
Local Oscillator and Reactance Tube 3-5
Power and Bias Circuitry 3-6
SECTION 4 MAINTENANCE 4-1
Introduction 4-1
Confirmation 4—1
Isolation 4-2
Troubleshooting the Spectrum Analyzer 4-3
SECTION 5 ALIGNMENT PROCEDURE 5-1
General 5-1
Local Oscillator 5-1
Dispersion 5-2
Log Scale 5-3
Input Attenuator Adjustment 5-3