Tektronix 511A Oscilloscoop
Fabrikant:
Model:
511A
Datum:
1950
Categorie:
Groep:
Omschrijving:
Cathode Ray Oscilloscope

Informatie

GENERAL DESCRIPTION The Tektronix Type 511-A Cathode Ray Oscilloscope is a wide range, portable instrument, making possible the observation of a wide variety of electrical waveshapes. It is primarily intended for laboratory and shop use, in the development and testing of all types of electronic equipment. The Type 511-AD Oscilloscope is identical to the Type 511-A except that it includes a factory installed Type 1-AD-25 Delay Network, which is described in Section VII of this manual. CHARACTERISTICS Signal observable 1. Sine waves from 10 cycles to 10 me. 2. Pulses of. 1 microsecond to 1 /50 sec. Sweep Circuit Hard tube type, either triggered or recurrent as desired. Sweep Speeds Continuously variable from .01 sec. per cm to .1 microsecond per cm. Trigger Requirements .5 to 50 V (Peak) sine wave or pulse of either polarity. Pulse as short as .05 microsecond will trigger satisfactorily. A key connected between TRIGGER INPUT and GND. is suitable for triggering single sweeps. Sweep Lag CRT is unblanked and sweep is operating linearly in less than .1 microsecond after receipt of an infinitely Sharp trigger pulse. Sweep Magnification Any desired 20% of the sweep can be spread over the entire trace except for sweep speeds faster than .5 microsecond per cm. External Sweep Input DC coupled via 100 K potentiometer and sweep Amplifier. Maximum deflection sensitivity 1.5 V per cm DC or peak to peak AC. Band width, DC to 800 kc (3 db down at 800 kc). Vertical Deflection Circuit Switch permits signal input connector on panel to be connected to deflection plates directly, via capacitor (RC=.l sec), via 1 Amplifier stage, or via 2 Amplifier stages. Input Attenuator Frequency compensated RC type with attenuation ratios of 2, 4, and 8. Vertical Deflection Sensitivity Without Amplifier 27 V per cm maximum, 200 V per cm minimum, DC or peak to peak AC. 1 Stage, 2.7 V per cm maximum, 40 V per cm minimum. 2 Stages, .27 V per cm maximum, 4 V per cm minimum. (Sensitivity is reduced by a factor of 10 when Probe is used.) In no case should the combined AC and DC input voltages exceed 600 V peak. Input Impedance 1 meg shunted by 40 mmfd (±5%) for any setting of the input selector and input attenuator. With Probe, 10 megohms shunted by 14 mmfd. Vertical Amplifier Bandwidth 1 stage, down 3 db (Max) (from 1 me response) at 5 cps and 10 me. 2 stages, down 3 db (Max) (from 1 me response) at 5 cps and 8 me. Vertical Amplifier Transient Response Rise time, 1 stage .04 miarosecond (10% to 90%) 2 stages .05 microsecond (10% to 90%) Calibrating Voltage Sine wave of power line frequency. Three ranges 0-1, 0-10, 0-100 v. peak to peak. Accuracy for line voltage of 117 v. is ±5% of full scale. May be measured with external meter when greater accuracy is required. A position on the SIGNAL CALIBRATE switch allows the use of an external calibrating source when desired. Waveforms available externally. Sweep sawtooth, 20 volts peak. Positive and negative gate, 40 V. peak, same duration as sweep. Connection to CRT Cathode via .1 mfd capacitor. RC=.012 sec. Accelerating voltage on cathode ray tube, 3 KV. Power Requirements. 105-125 volts, or 210-250 volts, 50-60 cycles, 230 watts. (See Section IV.) Weight. 50 pounds. Dimensions. 15Vi" high, 12Vz" wide, 21V2" deep. Finish. Panel, photo etched aluminum with black letters. Cabinet, gray wrinkle.

toon meer

Service-en gebruikershandleiding
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
73
Grootte:
10.80 Mbytes (11320619 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
Datum:
1950 01 01
Kwaliteit:
Gescand document alle leesbaar.
Upload datum:
2017 04 23
MD5:
9629530fb5deaff8c44e533fe74d3d81
Downloads:
1290

Informatie

SECTION I. General Description. Characteristics. Functions of Controls and Binding Posts. SECTION n. OPERATING INSTRUCTIONS. Sweep Circuit Adjustments. Adjustment of sweep stability. Function of trigger selector. Adjustment of trigger amplitude. Adjustment of sweep speed. Recurrent sweep. Single sweep. Ext. sweep input. Vertical Deflection System. Sweep magnifier. Video Amplifier. Direct connection to deflection plates. Calibration. Signal calibrate switch. Measurement of signal amplitudes. Intensity Modulation (Z axis). Sweep Output. Gate Outputs. SECTION m. CIRCUIT DESCRIPTION. Cathode Ray Tube Circuit. Sweep Chassis. Trigger phase splitter. Trigger Amplifier. Trigger coupling diode. Multivibrator. Unblanking circuit. Gate output Generator. Sweep Generator. Sweep output cathode follower. Sweep magnifier. Sweep Amplifier. Vertical Deflection System. Probe. Input attenuator. Video Amplifier. Calibrating circuits. SECTION IV. MAINTENANCE AND ADJUSTMENT. MAINTENANCE. Removal of Case. Cleaning. Inspection. Trouble Analyzing and Repair. General. Absence of power. Absence of spot on cathode ray tube. Power supply. Sweep circuits. Trigger circuits. Video Amplifier. Voltage and Continuity Tables. Average tube socket voltages. Point to point socket continuity. Transformer continuity. WAVEFORM PHOTOGRAPHS. Deflection Polarity Selector Waveforms. Power supply Waveforms. Sweep and Trigger Circuit Waveforms. Video Amplifier Waveforms. ADJUSTMENT. Operation on 210-250 Volt line. Adjustment of 225 Volt Regulated Supply. Adjustment of Sweep Speed Calibration. Adjustment of Input Attenuator. Adjustment of Video Amplifier H.F. Response. Adjustment of Video Amplifier L.F. Response. INTERIOR PHOTOGRAPHS. SECTION V. PARTS LIST. Abbreviations. Capacitors. Inductors. Resistors. Tube Complement. Switches. Transformers. Miscellaneous. Warranty. SECTION VI. DIAGRAMS. Block Diagram. Sweep and Trigger Circuits. Video Amplifier and CRT Circuits. Power supply Circuits. SECTION vn. VIDEO DELAY NETWORK.

toon meer