Quadtech Inc. Guardian 5000 Analyzer
Fabrikant:
Afbeelding 1 van 1
Als je nog andere foto's of handleidingen hebt voor de
Quadtech Inc. Guardian 5000 kun je de bestanden hier uploaden .
Model:
Guardian 5000
Datum:
1999
Categorie:
Groep:
Omschrijving:
Safety Analyzer
Informatie
The Guardian 5000 Safety Analyzer combines four critical
safety tests into a single
instrument, these being AC hipot, DC hipot, insulation
resistance measurements and
ground continuity test. The hipot test can be programmed
over a voltage range of 0.1 to
5KV AC and 0.5 to 6KV DC with a min/max leakage current
detection range of 300μA to
40mA AC and 20mA DC. Insulation resistance measurements are
possible to 10GΩ at
programmable DC test voltages between 100 and 1000V. A
ground continuity test to 30A
AC is also possible. The instrument comes standard with
internal storage of up to 50 memory
groups and an IEEE-488.2 Interface for remote control
operation and communication with
other instrumentation.
Handleidingen type:
Gebruikershandleiding
Pagina’s:
62
Grootte:
305.94 Kbytes (313280 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
150206/B3
Datum:
1999 11 01
Kwaliteit:
Elektronisch document, geen scan, zeer goed leesbaar.
Upload datum:
2017 01 29
MD5:
d929709f13aa57c9496813ca62735ed6
Downloads:
583
Informatie
Warranty
... v
Specifications
... vii
Introduction - Section 1
1.1 Unpacking and Inspection
... 1-1
1.1 Product
Overview ... 1-1
1.3 Front Panel
Description ... 1-2
1.4 Rear Panel Description
... 1-6
1.5 Accessories Included
... 1-7
1.6 Accessories/Options
Available ... 1-7
1.7 Power
Requirements ... 1-8
Operation - Section 2
2.1 Startup
... 2-1
2.2 Instrument Zeroing/Offset
... 2-1
2.3 Connection to Device Under Test
... 2-3
2.4 Measurement Procedure
... 2-6
2.5 Programming Test Modes
... 2-8
2.6 Programming Hipot Test
... 2-10
2.7 Programming Insulation Resistance (IR) Test
... 2-12
2.8 Programming Ground Continuity
Test ... 2-14
2.9 Initial Parameter
Setting ... 2-16
2.10 Front Panel Lockout
... 2-18
2.11 Software Version
Display ... 2-18
2.12 Clear Setup
Memory ... 2-18
Input/Output Interfaces - Section 3
3.1
Remote ... 3-1
3.2 IEEE-488
Interface ... 3-3
3.2.1 Description
... 3-3
3.2.2 Interface
Commands ... 3-4
3.2.2.1 Listener Functions
... 3-5
3.3.2.2 Talker
Functions ... 3-9
3.2.3 Sample QuickBASIC
Program ... 3-11
3.3 Scanner Interface
... 3-14
3.3.1 Scanner Accessories
... 3-14
3.3.2 Scanner Card Installation
... 3-14
3.3.3 Scanner Connections
... 3-15
3.3.4 Scanner Programming
... 3-17
3.4 G16 International Power
Strip ... 3-19
4.1 General
... 4-1
4.2 Instrument
Return ... 4-1
4.3 Calibration
... 4-1
4.3.1 Calibration
Procedure ... 4-2
4.3.2 AC Voltage
Calibration ... 4-3
4.3.3 DC Voltage
Calibration ... 4-4
4.3.4 IR Voltage Calibration
... 4-4
4.3.5 AC Current Calibration
... 4-5
4.3.6 DC Current Calibration
... 4-6
4.3.7 GC
Calibration ... 4-7
4.3.8 Finalize Calibration
... 4-8