Apparatuur informatie:

Electronic Navigation Industries A-300 Versterker
Fabrikant:
Electronic Navigation Industries
Model: A-300
Datum:
Categorie: Radio, Communicatie
Groep: Versterker
Beschrijving: BROADBAND POWER AMPLIFIER
Informatie:
                                    The ENI Model A300 is an all solid state amplifier which has
a flat frequency response from .3 MHz to 35 MHz. It provides
300 watts of linear power with low harmonic and
intermodulation distortion. Gain is 55 dB nominal, with a
variation of less than ± 1.0 dB over the entire frequency
range. Input and output impedance are 50 ohms and the unit
may be driven to full power output by most RF synthesizers,
signal generators and swept signal sources.
The ENI Model A300 will deliver its rated power output into
any load impedance, regardless of match. Built-in protection
circuitry will absorb the power reflected from a mismatched
load without causing failure or oscillation.
Output RF voltage is displayed on the front panel meter. The
Model A300 is packaged for bench mounting and is shipped
with rack mounting adapters. Its integral power
supply and cooling operate from a 115 or 230 V ac 50/60 Hz
main supply.
The Model A300 will raise the power level of signal sources
and generators without requiring tuning or band- switching.
The Class A linear circuitry will amplify signals of AM, FM,
SSB, TV and complex modulations limited only by their peak
input and bandwidth, with minimum distortion.

Deze handboeken zijn beschikbaar voor de bovengenoemde apparatuur:

Electronic Navigation Industries -- A-300 -- Service-en gebruikershandleiding
File name: ENI-7571-Manual-Page-1-Picture
Handleidingen Type: Service-en gebruikershandleiding
Pagina's: 31
Maat: 1.60 Mbytes (1673279 Bytes)
Taal: Engels
Herziening van:
Manual-ID/Number:
Datum:
Kwaliteit: Gescande document, lezen deels slecht, deels niet leesbaar.
Upload datum:
MD5: 8831ab8fd7b5899ced065e1324208e5a
Downloads: 102 Sinds 25 januari 2016
Informatie:
CHAPTER 1 GENERAL INFORMATION 1-1
1.1 introduction................................. 1-1
1.2 Specifications............................... 1-1
1.3 instrument Identification............. 1-1
CHAPTER 2 PREPARATION 2-1
2.1 Initial Inspection .......................... 2-1
2.1.1 Mechanical Check ........................ 2-1
2.1.2 Claim for Damage ........................ 2-1
2.1.3 Performance Check.................... 2-1
2.2 Preparation for Use..................... 2-1
2.2.1 Power Requirements............... . 2-1
2.2.2 Power Cable Ground Protection . 2-1
2.2.3 Cooling........................................ 2-2
2.3 Rack Mounting............................ 2-2
2.4 Packaging for Reshipment ..... 2-2
CHAPTER 3 OPERATION 3-1
3.1 Functional Description............... 3-1
3.2 Controls, Indicators and
Connectors............................... 3-1
3.3 Operating Procedure..................... 3-1
3.4 Precautions.............................. 3-1
CHAPTER 4 PRINCIPLES OF OPERATION 4-1
4.1 General........................................ 4-1
4.2 Block Diagram Description .... 4-1
4.2.1 Driver Amplifier Module {A48A}
A300-4382 ............................... 4-1
4.2.2 Power Amplifier Module (A40A)
A300-4381 ............................... 4-1
4.2.3 Bias Regulator Module (A49)
A300*4387............................... 4-1
4.2.4 Four-Way Splitter/Combiner
Module (A50) A300-4383 ... 4-3
4.2.5 Two-Way Output Combiner
Module (A51) A300-4384 ... 4-3
4.2.6 RF Voltmeter Module
(A29M) A300-4386 ............... 4-3
4.2.7 Power Distribution
A300-2381 ............................... 4-3
CHAPTER 5 PERFORMANCE
TEST PROCEDURES 5-1
5.1 Performance Tests . ..................... 5-1
5.1.1 General .......................................... 5-1
5.1.2 Test Equipment Required.......... 5-1
5.1.3 Gain and Gain Variation Test.. . 5-1
5.1.3.1 Calibration of Set Up.................. 5-1
Paragraph Page
5.1.3.2 Measurement Procedure............. 5-1
5.1.4 RF Output Power Test............... 5-2
5.1.4.1 Measurement Procedure............. 5-2
5.1.5 RF Output Distortion Test .... 5-2
5.1.5.1 Measurement Procedure ............. 5-2
CHAPTER 6 TROUBLESHOOTING AND REPAIR 6-1
6.1 Troubleshooting............................ 6-1
6.2 Locating Faulty RF Module.... 6-2
6.2.1 General........................................ 6-2
6.2.2 Isolating Amplifier Problem ... . 6-2
6.2.2.1 Two-Way Output Combiner
Test {A51> A300-4383 .......... 6-3
6.2.2.2 Heatsink Assembly Test
A300-3385.............................. 6-3
6.2.2.2.1 Bias Voltage Check...................... 6-3
6.2.2.2.2 RF Power Test............................ 6-3
6.2.2.3 Driver Amplifier Module
(A48A) A300-4382 ............... 6-4
6.2.3 RF Voltmeter
(A29M) A300-4386 .................. 6-4
6.2.3.1 Alignment Procedure................. 6-4
6.3 DC Power Supply ...................... 6-4
6.3.1 General . . .................................. 6-4
6.3.2 Test Procedure............................ 6-5
6.4 Disassembly Procedure............... 6-5
6.4.1 General........................................ 6-5
6.4.2 Tools Required........................... 6-5
6.4.3 Removal of Cover...................... 6-5
6.4.4 Driver Amplifier Heatsink
Assembly A300-3386 ............. 6-5
6.4.5 Power Supply Regulator
Board {A53A) A300-4385 ... 6-5
6.4.6 Power Amplifier Heatsink
Assembly A300-3385 ...... 6-5
6.4.7 Power Amplifier Power Supply
A300-3387 .............................. 6-6
6.4.8 Driver Amplifier Power Supply
A300-3388...................... 6-6
6.4.9 Four-Way Splitter/Combiner
Module (A50) A300-4383 ... 6-6
6.4.10 Power Amplifier Module
(A40A) A300-4381 ............... 6-6
6.4.11 Two-Way Output Combiner
(A51) A300-4383 ................. 6-6
CHAPTER 7 SCHEMATICS AND PARTS LIST 7-1
7.1 Schematic Diagrams .................... 7-1
7.2 Parts List................................ 7-1
7.3 List of Manufacturers.................. 7-1
7.4 Ordering Replacement Parts. ... 7-1
ENI-7571-Manual-Page-1-Picture
Start gratis downloaden


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Type the numbers for four hundred seventy-two.
Powered by Commentics