California Instruments 848T Voeding
Fabrikant:
Model:
848T
Datum:
1983
Categorie:
Groep:
Omschrijving:
AC Power controller

Informatie

Th-e California Instruments’ Model 848TCM AC Power Controller is designed as a Plug-In controller of frequency and waveform amplitude. The 848TCM will plug into and obtain power from all California Instruments AC Power Sources. The frequency and amplitude are locally controllable by a front panel keyboard or remotely programmable by the IEEE-488 interface. Option PC for the associated power source is required to mount the IEEE-488 Interface connector in its rear panel. The output of the Model 848TCM provides three-phase variable frequency and amplitude drive for the power source, The remote sense input monitors the voltage across the load. The voltage at the sense point will be maintained by the Model 848TCM to be equal to the programmed value. In the event that this voltage cannot be maintained, the Model 848TCM will automatically set the output voltage to zero volts and then step the output voltage in five volt increments to the programmed value. If the programmed voltage is still not maintainable, the Model 848TCM will set the programmed voltage to zero volts and display an error message coincident with the phase or phases generating the fault. The Model 848TCM employs digital techniques for control of the output frequency. A crystal controlled Oscillator serves as the clock for the digital frequency Generator that controls the output frequency. This circuit configuration provides the same long-term frequency stability as the crystal time base. The crystal time- base is adjusted at the factory for a frequency accuracy of ±5 ppm. The output frequency will, therefore, be equal to ±5 ppm of the programmed frequency* The Model 848TCM is capable of operating from 45 Hz to 9999 Hz, 999.9 Hz or 99.99 Hz in 1 Hz, .1 Hz or .01 Hz steps depending on the frequency range (see paragraph 1.3). The low end of the frequency range is limited by a frequency detector to 45 Hz. The high end is factory adjusted to the upper full power frequency limit of the associated power source. If an attempt is made to program the frequency outside these frequency limits the amplitude will default to zero volts and the display will show the error message E 71. The Model 848TCM must be used on the 135 volt range when used with a power source on the 120, 130 or 135 volt range. It must be on the 2 70 volt range when used with a power source on the 240, 260 or 270 volt range.

toon meer

Service-en gebruikershandleiding
Handleidingen type:
Service-en gebruikershandleiding
Pagina’s:
50
Grootte:
1.51 Mbytes (1583927 Bytes)
Taal:
english
Herziening:
Handleidingen-ID:
Datum:
Kwaliteit:
Gescande document, lezen deels slecht, deels niet leesbaar.
Upload datum:
2015 12 20
MD5:
460f2aa6332756415e2c4b6aa3d69163
Downloads:
498

Informatie

SECTION 1 GENERAL DESCRIPTION 1.1 INTRODUCTION 1 1.2 - . SPECIFICATIONS 1 1,3 INSTRUMENT IDENTIFICATION 1 1.3,1 OPTIONS 1 1.4 DESCRIPTION 3 l.S ACCESSORY EQUIPMENT 3 SECTION 2 INSTALLATION 2.1 GENERAL 4 2.2 UNPACKING 4 2.3 POWER REQUIREMENTS 4 2.4 FUSE REQUIREMENTS 4 2.5 POWER SOURCE INTERCONNECTION 4 2.6 Interface CONNECTIONS 5 2. 7 FREQUENCY/AMPLITUDE PROGRAM RANGE OPTIONS 5 2.8 ACCEPTANCE TEST 7 SECTION 3 OPERATION 3.1 GENERAL 9 3.2 DISPLAY 9 3.2.1 ANNUNCIATORS 9 3.2.2 CHARACTER 9 3.2.3 ERROR MESSAGES 9 3.3 LOCAL OPERATION 12 3.3.1 NUMBER KEYS 12 3.3.2 FREQUENCY ENTER 12 3.3.3 AMPLITUDE ENTER 12 3.3.4 PROGRAM REGISTER 12 3.3.5 RECALL REGISTER 14 3.3.6 SERVICE REQUEST 14 3.4 REMOTE OPERATION 14 3.4.1 ADDRESS SELECTION 14 3.4.2 LISTEN ONLY 17 3.4.3 MESSAGE FORMAT 17 3.4,3.1 PROGRAM HEADER 18 3. 4. 3.1.1 AMPLITUDE 19 3.4.3.1.2 FREQUENCY 19 3.4.3.1.3 RANGE 19 3.4.3.1.4 PROGRAM 19 3.4.3.1.5 RECALL 19 3.4.3.1.6 TRIGGER 20 3.4.3.2 DATA FIELDS 20 3. 4. 3. 2.1 UNSIGNED VALUE KITH DECIMAL POINT 20 3. 4.3.2.2 UNSIGNED VALUE KITH DECIMAL POINT AND EXPONENT 21 3.4.3.3 DELIMITER 21 3.4. 3 . 4 NULL CHARACTERS 21 3.4.4 SERVICE REQUEST 2 2 3.4.4.1 STATUS BYTE 22 3.4.5 Hewlett Packard SERIES 8 0 CONTROLLER PROGRAMMING 23 3.4.5.1 SERIES 8 0 CONTROLLER STATEMENTS 24 3.4.5.1.1 OUTPUT 24 3.4.5.1.2 TRIGGER 24 · 3.4.5.1.3 SERVICE REQUEST STATEMENTS 24

toon meer