Electronic Navigation Industries 350L Amplificatore
Produttore:
Modello:
350L
Data:
0
Categoria:
Gruppo:
Descrizione:
BROADBAND POWER AMPLIFIER

Informazioni

The ENi Model 350L is an all solid state Amplifier which has a flat frequency response from 250 kHz to 105 MHz. It provides 50 watts of linear power with low harmonic and intermodulation distortion. Gain is 50 dB nominal, with a variation of less than +1.5 dB over the entire frequency range. Input and output impedance are 50 ohms and the unit may be driven to full power output by most RF synthesizers, signal generators and swept signal sources. The ENI Model 350L will deliver its rated power output into any load impedance, regardless of match, Buiit-in protection circuitry will absorb the power reflected from a mismatched load without causing failure or oscillation. Output RF voltage is displayed on the front panel meter. The Model 350L is packaged for bench mounting and is shipped with rack mounting adapters. Its integral power supply and cooling operate from a 115 or 230 VAC 50/60Hz main supply. The Model 350L will raise the power level of signal sources and generators without requiring tuning or band- switching. The Class A linear circuitry will amplify signals of AM, FM, SSß, TV and complex modulations limited only by their peak input and bandwidth with minimum distortion.

mostra più dettagli

Manuale d'uso
Tipo di manuale:
Manuale d'uso
Pagine:
16
Dimensione:
525.22 Kbytes (537824 Bytes)
Lingua:
english
Revisione:
ID del manuale:
Data:
Qualità:
Documento scansionato, la lettura in parte male, non in parte leggibile.
Data caricamento:
2016 01 25
MD5:
42d3c760fea09431ddcc91c6820d0f01
Scaricamenti:
624

Informazioni

CHAPTER 1 INTRODUCTION 1.1 General Description ... 1-1 1.2 Specifications ... M 1.3 Instrument Identification . . . . 1-1 CHAPTER 2 PREPARATION 2.1 Initial Inspection ... 2-1 2.1.1 Mechanical Check ... 2-1 2.1.2 Claim for Damage ... 2-1 2.1.3 Performance Check ... 2-1 2.2 Preparation for Use ... 2-1 2.2.1 Power Requirements ... 2-1 2.2.2 Power Cable Ground Protection , 2-1 2.2.3 Cooling ... 2-1 2.3 Rack Mounting ... 2-1 2.4 Packaging for Reshipment . . . . 2-1 CHAPTER 3 OPERATION 3.1 Functional Description ... 3-1 3.2 Controls, Indicators and Connectors ... 3-1 3.3 Operating Procedure ... 3-1 3.4 Precautions ... 3-2 CHAPTER 4 PRINCIPLES OF OPERATION 4.1 General ... 4-1 4.2 Block Diagram Description . , , 4-1 4.2.1 Preamplifier Module (A22) 3501.-4185 ■ ... 4-1 4.2.2 Driver Amplifier Module (A1) 350L-4181 ... 4-1 4.2.3 Power Amplifier Module (A21) 350L-4184 ... 4-1 4.2.4 Combiner Module (A23) 350L-4186 ... 4-3 4.2.5 RF Voltmeter Module (A 12) 350L-4182 ... 4-3 4.2.6 Power Distribution 350L-2181 ... 4-3 CHAPTER 5 PERFORMANCE TEST PROCEDURES 5.1 Performance Tests ... 5-1 5.1.1 General , , ... . . 5-1 5.1.2 Test Equipment Required . , , . . 5-1 5.1.3 Gain and Gain Variation Test . . · 5-1 5,1.3.1 Calibration of Set Up ... . . 5-1 Paragraph Page 5.1.3.2 Measurement Procedure ... 5-1 5.1.4 RF Output Power Test ... 5-2 5.1.4.1 Measurement Procedure ... 5-2 5.1.5 RF Output Distortion Test ... 5-2 5.1.5.1 Measurement Procedure ... 5-2 CHAPTER 6 TROUBLESHOOTING AND REPAIR 6.1 Troubleshooting ... 6-1 The end of the manual with schematics is missing!

mostra più dettagli