Simpson 260 Series 7M Multimètre analogique
Fabricant:
Modèle:
260 Series 7M
Date:
1981
Catégorie:
Groupe:
Description:
Volt-Ohm-Milliammeter

Information

The Simpson Volt-Ohm-Milliammeters 260 Series 7 and Series 7M (hereafter referred to as the 260 or as the Instrument), are identical instruments electrically and mechanically, except that the Series 7M is equipped with a mirrored dial to eliminate parallax (Figures 1-1 and 1-2). The 260 Series 7 is a rugged, accurate, compact, easy-to-use instrument. The Instrument can be used to make accurate measurements of AC and DC voltage, direct current, resistance, decibels, and Output Voltage. The Output Voltage function is used for measuring the AC component of a mixture of AC and DC voltage. This occurs primarily in Amplifier circuits. 1.1.2 New Features in the 260-7 and 7M are: • New connectors between the Instrument and the test leads which eliminates a shock hazard in the event a connector is inadvertently pulled out of the Instrument jack. • A high energy fuse F2 which is now in the BATTERY AND FUSE COMPARTMENT, and accessible without removing the Instrument case. • An OFF/TRANSIT position which has been added to the function switch to protect the meter movement during transit. (This, position shunts the meter movement and opens the internal connections to the COMMON and + jacks.) • A test lead set with molded elbow prods at one end for connection to the front panel input terminals and test probes at the other end. The test probes have a non-slip grip surface and a barrier to maintain the spacing between the user’s fingers and the Probe tip. Threaded shoulders at the Probe tip accept screw-on alligator clips (supplied) or an accessory AC or DC 5000 volt range extending probes.

plus

Service et Manuel de l'utilisateur
Type manuel:
Service et Manuel de l'utilisateur
Pages:
60
Taille:
1.66 Mbytes (1740323 Bytes)
Langue:
english
Révision:
third
Manuel-ID:
6-111452
Date:
Qualité:
Document scanné, la lecture en partie mal, en partie illisible.
Date de transfert:
2014 11 22
MD5:
bf9c1826bf70b401a0f87f4040466e56
Téléchargements:
3213

Information

SECTION I Introduction ... 1-1 1.1 General ... 1-1 1.2 Description ... 1-2 1.3 Internal Batteries ... 1-3 1.4 Printed Circuit ... 1-3 1.5 Phenolic Case ... 1-3 1.6 Adjust-A-Vue Handle ... 1-4 1.7 Test Leads ... 1-4 1.8 Technical Data ... 1-5 1.9 Definition of Accuracy ... 1-7 1.10 Safety Considerations ... 1-7 SECTION II Installation ... 2-1 2.1 General ... 2-1 2.2 Unpacking and Inspection ... 2-1 2.3 Warranty ... 2-1 2.4 Shipping ... 2-2 2.5 Power Source Requirements ... 2-2 2.6 Operating Position ... 2-2 SECTION ΙΠ Controls, Jacks, and Indicators ... 3-1 3.1 General ... 3-1 3.2 Front Panel Description ... 3-1 SECTION IV Operation ... 4-1 4.1 General ... 4-1 4.2 Safety Precautions ... 4-1 4.3 Polarity Reversing ... 4-3 4.4 Measurement of Unknown Voltage or Current . . 4-4 4.5 Test Leads ... 4-4 4.6 DC Voltage Measurement 0-250 mV Range ... '4-4 4.7 DC Voltage Measurement 0-1V Range ... 4-5 4.8 DC Voltage Measurement 0-2.5 Through 0-500V Range ... 4-7 4.9 DC Voltage Measurement 0-1000V Range ... 4-8 4.10 AC Voltage Measurement 0-2.5 Through 0-500V Range ... 4-10 4.11 AC Voltage Measurement 0-1000V Range ... 4-12 4.12 Output Voltage Measurement ... 4-13 4.13 Decibel Measurements (—20 to +50 dB) ... 4-15 4.14 Direct Current Measurement ... 4-18 4.15 Direct Current Measurement 0-50/; A Range ... 4-18 4.16 Direct Current Measurement 0-1 mA Through 0-500 mA Range ... 4-20 4.17 Direct Current Measurement 0-10A Range ... 4-21 4.18 Resistance Measurements ... 4-22 4.19 Measuring Resistance ... 4-22 4.20 Resistance Measurement of Semiconductors ... 4-24 SECTION V Operator Servicing ... 5-1 5.1 General ... 5-1 5.2 Inspection ... 5-1 5.3 Battery Replacement ... 5-1 5.4 Fuse Replacement ... 5-2 5.5 Test Lead Inspection ... 5-4 5.6 Care ... 5-4 SECTION VI Servicing Instructions ... 6-1 6.1 General ... 6-1 6.2 Removing the Instrument Case ... 6-1 6.3 Replacement Parts and Schematic Diagram ... 6-1

plus