Keithley 7066 Interface
Fabricant:
Pas d'image disponible!
Peut-être que vous pouvez envoyer une image pour le
Keithley 7066 ?
Si vous avez d'autres manuels pour les
Keithley 7066, vous pouvez télécharger les fichiers ici .
Modèle:
7066
Date:
1990
Catégorie:
Groupe:
Description:
Relay Switch Card
Information
The Model 7066 Relay Switch Card provides 10 separate channels
using 101wo-pole relays. As shipped, the switches are configured
for double-pole single-throw (DPST), normally open (NO)
operation, Features of the relay switch card include:
• Quick disconnect terminal blocks for each channel.
• Moveable relay jumpers to configure any switch to be
normally closed (NC).
• Separate, isolated IN/OUT circuits for each channel.
Type manuel:
Service et Manuel de l'utilisateur
Pages:
46
Taille:
966.00 Kbytes (989184 Bytes)
Langue:
english
Révision:
B
Manuel-ID:
7066-901-01
Date:
Qualité:
Document scanné, tous les lisible.
Date de transfert:
2014 03 02
MD5:
5cb072b5436f9c6f063785de4d4e3293
Téléchargements:
840
Information
SECTION 1—GENERAL INFORMATION
1.1 INTRODUCTION ... 1-1
1.1.1 Product Description ... 1-1
1.1.2 Manual Overview ... 1-1
1.2 WARRANTY INFORMATION ... 1-2
1.3 MANUAL ADDENDA ... 1-2
1.4 SAFETY SYMBOLS AND TERMS ... 1-2
1.5 UNPACKING AND INSPECTION ... 1-3
SECTION 2—OPERATION
2.1 INTRODUCTION ... 2-1
2.2 SAFETY PRECAUTIONS ... 2-1
2.3 WIRING ... 2-1
2.3.1 NO and NC Jumpers ... 2-3
2.3.2 DPST Configuration ... 2-3
2.3.3 Terminal Block Configuration ... 2-5
2.3.4 Other Configurations ... 2-8
2.4 INSTALLATION AND REMOVAL ... 2-12
2.4.1 Relay Card Installation ... 2-13
2.4.2 Relay Card Removal ... 2-13
2.5 OPERATION ... 2-13
2.6 TYPICAL APPLICATIONS ... 2-23
2.6.1 Switching Sources and Supplies ... 2-23
2.6.2 Switching Loads ... 2-24
2.6.3 Other Applications ... 2-25
SECTION 3—SERVICING INFORMATION
3.1 INTRODUCTION ... 3-1
3.2 REQUIRED TEST EQUIPMENT ... 3-1
3.3 ENVIRONMENTAL CONDITIONS ... 3-1
3.4 VERIFICATION PROCEDURE ... 3-2
SECTION 4—REPLACEABLE PARTS
4.1 INTRODUCTION ... 4-1
4.2 REPLACEABLE PARTS ... 4-1
4.3 ORDERING INFORMATION ... 4-1
4.4 FACTORY SERVICE ... 4-1
4.5 COMPONENT LAYOUT and SCHEMATIC
DIAGRAM ... 4-2
SECTION 2—OPERATION
2-1 Four-Pole Jumper Configuration
... 2-16
2-4 Scanner Control of Model 7066 1-Pole Mode . . . 2-17
2-5 Scanner Control of Model 7066 Matrix Mode
(0-Pole) ... 2-19
SECTION 3—SERVICING INFORMATION
3-1 Recommended Test Equipment ... 3-1
SECTION 4—REPLACEABLE PARTS
4-1 Model 7066
Parts List ... 4-2
Type manuel:
Service et Manuel de l'utilisateur
Pages:
40
Taille:
1.01 Mbytes (1061842 Bytes)
Langue:
english
Révision:
B
Manuel-ID:
7066-901-01
Date:
1990 02 01
Qualité:
Document scanné, tous les lisible.
Date de transfert:
2018 08 24
MD5:
d755ccaed3a28f6318ffc63ce288d371
Téléchargements:
610
Information
Manual Overview
The instruction manual is organized in the following manner:
• Section 1 General Information—Includes a product
description and an overview of the manual, information on
warranty manual addenda, safety symbols and terms, unpacking
and inspection, and specifications.
• Section 2 Operation—Includes safety information, wiring
and installation, operating instructions, and some typical
applications.
• Section 3 Performance Verification—Provides the procedure
to check proper operation of the card.
• Section 4 Replaceable Parts—Includes a parts list,
schematic diagram and a component layout.