Keithley 7012-C Plug-In
Manufacturer:
Model:
7012-C
Date:
1991
Category:
Group:
Description:
Quad 1 x 10 Multiplexer Card

Information

Features The Model 7012 is a low voltage, two-pole, quad, 1 x 10 multiplexer card. Some of the key features include: Low contact potential and offset current for minimal effects on low-level signals. The connector board detaches from the relay board allowing easy access to the screw terminals (Model 7012-S) and jumpers. Easy jumper configuration of one, two, three or four multiplexer banks. Backplane jumpers. Cutting jumpers disconnects multiplexer bank outputs from the Model 7001 analog backplane.

show more

Service and User Manual
Manual type:
Service and User Manual
Pages:
91
Size:
1.96 Mbytes (2050048 Bytes)
Language:
english
Revision:
B
Manual ID:
7012-901-01
Date:
1993 11 01
Quality:
Scanned document, all readable.
Upload date:
2018 08 24
MD5:
859e2811b76f5facd93c9b3c43b6d808
Downloads:
1027

Information

Introduction ... 1-1 Features ... 1-1 Warranty information ... 1-2 Manual addenda ... 1-2 Safety symbols and terms ... 1-2 Specifications ... 1-2 Unpacking and inspection ... 1-2 Inspection for damage ... 1-2 Shipping contents ... 1-2 Instruction manual ... 1-3 Repacking for shipment ... 1-3 Optional accessories ... 1-3 Introduction ... 2-1 Basic matrix configuration (4 × 10) ... 2-1 Typical matrix switching schemes ... 2-3 Single-ended switching ... 2-3 Differential switching ... 2-4 Sensing ... 2-4 SMU connections ... 2-5 Matrix expansion ... 2-5 Two-card switching systems ... 2-5 Mainframe matrix expansion ... 2-9 Introduction ... 3-1 Handling precautions ... 3-1 Connections ... 3-1 Backplane row jumpers ... 3-2 Screw terminal connector card ... 3-2 Multi-pin (mass termination) connector card ... 3-4 Typical connection schemes ... 3-9 Single card system ... 3-9 Two-card system ... 3-9 Two-mainframe system ... 3-14 Model 7012 installation and removal ... 3-14 Introduction ... 4-1 Power limits ... 4-1 Mainframe control of matrix card ... 4-1 Channel assignments ... 4-2 Front panel control ... 4-4 IEEE-488 bus operation ... 4-4 Matrix switching examples ... 4-5 Thick film resistor network testing ... 4-5 Transistor testing ... 4-10 Measurement considerations ... 4-13 Path isolation ... 4-13 Magnetic fields ... 4-14 Radio frequency interference ... 4-14 Ground loops ... 4-14 Keeping connectors clean ... 4-15 AC frequency response ... 4-15 Introduction ... 5-1 Handling and cleaning precautions ... 5-1 Performance verification ... 5-2 Environmental conditions ... 5-2 Recommended equipment ... 5-2 Matrix card connections ... 5-3 Channel resistance tests ... 5-3 Offset current tests ... 5-4 Contact potential tests ... 5-6 Path isolation tests ... 5-7 Differential and common-mode isolation tests ... 5-9 Special handling of static-sensitive devices ... 5-11 Principles of operation ... 5-12 Block diagram ... 5-12 ID data circuits ... 5-13 Relay control ... 5-13 Relay power control ... 5-14 Power-on safeguard ... 5-14 Troubleshooting ... 5-15 Troubleshooting equipment ... 5-15 Troubleshooting access ... 5-15 Troubleshooting procedure ... 5-15 Introduction ... 6-1 Parts lists ... 6-1 Ordering information ... 6-1 Factory service ... 6-1 Component layouts and schematic diagrams ... 6-2

show more

User Manual
Manual type:
User Manual
Pages:
64
Size:
2.04 Mbytes (2142617 Bytes)
Language:
english
Revision:
B
Manual ID:
7012-901-01
Date:
1993 11 01
Quality:
Scanned document, all readable.
Upload date:
2018 08 24
MD5:
e0d7ac42a9c58a009cc8495b4c858cdf
Downloads:
787