Equipment information:

Electronic Navigation Industries 3100L Amplifier
Manufacturer:
Electronic Navigation Industries
Model: 3100L
Date:
Category: Radio, Communication
Group: Amplifier
Description: BROADBAND POWER AMPLIFIER
Information:
                                    The ENI Model 3100L is an all solid state amplifier which
has a flat frequency response from 250 kHz to 105 MHz.
It provides 100 watts of linear power with low harmonic and
intermodulation distortion. Gain is 50 dB nominal, with a
variation of less than +1.5 dB over the entire frequency
range, input and output impedance are 50 ohms and the unit
may be driven to full power output by most RF synthesizers,
signal generators and swept signal sources.
The ENI Model 3100L will deliver its rated power output into
any load impedance, regardless of match. Built-in protection
circuitry will absorb the power reflected from a mismatched
load without causing failure or oscillation.
Output RF voltage is displayed on the front pane! meter. The
Model 3100L is packaged for bench mounting and is shipped
with rack mounting adapters. Its integral power
supply and cooling operate from a 115 or 230 VAC 50/60Hz
main supply.
The Model 3100L will raise the power level of signal sources
and generators without requiring tuning or band- switching.
The Class A linear circuitry will amplify signals of AM, FM,
SSB, TV and complex modulations limited only by their peak
input and bandwidth, with minimum distortion.

These manuals are available for the above equipment:

Electronic Navigation Industries -- 3100L -- User Manual
File name: ENI-7551-Manual-Page-1-Picture
Manual Type: User Manual
Pages: 24
Size: 1.00 Mbytes (1049801 Bytes)
Language: english
Revision:
Manual-ID/Number:
Date:
Quality: Scanned document, reading partly badly, partly not readable.
Upload date:
MD5: 16f01233d53bea30fee52c484314ec8b
ed2kID: 2ee1bc117b39d89dce79de8dd109e0d1
Downloads: 23 since 25 January 2016
Information:
CHAPTER 1 INTRODUCTION
1.1 General Description . . ................ 1-1
1.2 Specifications............................... 1-1
1.3 Instrument Identification .... 1-1
CHAPTER 2 PREPARATION
2.1 initial inspection ....................... 2-1
2.1.1 Mechanical Check............... 2-1
2.1.2 Claim for Damage .................... 2-1
2.1.3 Performance Check................ . 2-1
2.2 Preparation for Use............... 2-1
2.2.1 Power Requirements. .................. 2-1
2.2.2 Power Cable Ground Protection . 2-1
2.2.3 Cooling......................................... 2-1
2.3 Rack Mounting ......................... 2-1
2.4 Packaging for Reshipment .... 2-2
CHAPTER 3 OPERATION
3.1 Functional Description ............. 3-1
3.2 Controls, Indicators and
Connectors ............................ 3-1
3.3 Operating Procedure.................. 3-1
3.4 Precautions.................................... 3*2
CHAPTER 4 PRINCIPLES OF OPERATION
4.1 General......................................... 4-1
4.2 Block Diagram Description . . . 4-1
4.2.1 Preamplifier Module (A27)
3100L-4204 ............................ 4-1
4.2.2 Driver Amplifier Module (A1)
350L-4181.............................. 4-1
4.2.3 Power Amplifier Module (A21)
350L-4184............................... 4-1
4.2.4 Combiner Module (A28)
3100L-4205 .................... 4-3
4.2.5 RF Voltmeter Module {A29}
3100L-4206 ............................ 4-3
4.2.6 Power Distribution
(3100L-2201)............................ 4-3
CHAPTER 5 PERFORMANCE
TEST PROCEDURES
5.1 Performance Tests.......................... 5*1
5.1.1 General .............................. 5-1
5.1.2 Test Equipment Required ........... 5-1
5.1.3 Gain and Gain Variation Test ... 5-1
5.1.3.1 Calibration of Set Up .................. 5-1
Paragraph Page
5.1.3.2 Measurement Procedure...................5-1
5.1.4 RF Output Power Test ......................5-2
5.1.4.1 Measurement Procedure ...................5-2
5.1.5 RF Output Distortion Test ..... 5-2
5.1.5.1 Measurement Procedure...................5-2
CHAPTER 6 TROUBLESHOOTING AND REPAIR
6.1 Troubleshooting................................6-1
6.2 Locating Faulty RF Module .... 6-2
6.2.1 General...............................................6-2
6.2.2 Isolating Amplifier Problem..............6-2
6.2.2.1 Combiner Module (A28) Test . . . 6-3 δ.2.2.2
Preamplifier Module (A27)
Test...............................................6-3
6.2.2.3 Heatsink Assembly Test
(3100L-3206 and 3207)..............6-3
6.2.2.3.1 Bias Voltage Check..............................6.-3
6.2.2.3.2 RF Power Test ...................................6-3
6.2.3 RF Voltmeter (A29).........................6-4
6.2.3.1 Alignment Procedure ........... .. 6-4
6.3 DC Power Supply ..............................5.4
6.3.1
General................................................-0.4
6.3.1.1 Test Procedure...................................5.4
6.3.1.2 Adjustment Procedure......................5.4
6.4 Disassembly Procedures....................5.4
6.4.1 Genera!................................................g.4
6.4.2 Tools Required .................................5.5
6.4.3 Removal of Cover.............................g.g
6.4.4 Preamplifier Module (A27)
3100L-4204 and Combiner
Module (A28) 3100L-4205 ... 6-5
6.4.5 Power Supply Regulator Board
{A26) 310QL-4203.......................6-5
6.4.6 Heatsink Assemblies
(3100L-3206 and 3207)...............6-5
6.4.7 Transistor Assemblies
(350L-4188).................................6-5
6.4.8 Driver Amplifier Module {A1)
350L-4181 ....................................6-5
6.4.9 Power Amplifier Module {A21)
350L-4184....................................6-6
ENI-7551-Manual-Page-1-Picture
Start Free Download


Comments

No comments yet.

Add Comment

* Required information
(never displayed)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
Enter the third letter of the word castle.
 
Enter answer:
 
Notify me of new comments via email.
 
Remember my form inputs on this computer.
 
 
Powered by Commentics