Equipment information:

California Instruments 6000L-P Power supply
Manufacturer:
California Instruments
Model: 6000L-P
Date: 2001
Category: Measurement instruments
Group: Power supply
Description: Power Source
Information:
                                    This power system is a high efficiency power source that
provides a low distortion output. The output can be
configured in either a single or three-phase configuration.
A number of Power Sources can be configured to supply full
output power up to 27000VA. Table 1-1 shows the output VA
per phase for each of the available power system models. The
table also shows that increased power is available at a
reduced operating temperature of 35?C.

These manuals are available for the above equipment:

California Instruments -- 6000L-P -- Service and User Manual
File name: CaliforniaInstruments-7412-Manual-Page-1-Picture
Manual Type: Service and User Manual
Pages: 151
Size: 1.28 Mbytes (1345007 Bytes)
Language: english
Revision: K
Manual-ID/Number: 4009-316
Date: August 2001
Quality: Scanned document, all readable.
Upload date:
MD5: d4f10b1e9514dd42297132951bea20a5
ed2kID: 8ea051106775a731920e8812145cbaca
Downloads: 54 since 20 December 2015
Information:
SECTION 1 INTRODUCTION AND
SPECIFICATIONS--------------------------------------------------------------------------1
1.1
INTRODUCTION............................................................................................................................................1
1.2 GENERAL DESCRIPTION
-------------------------------------------------------------------------------------------------------
1
1.3 ACCESSORY EQUIPMENT/RACK
SLIDES-------------------------------------------------------------------------------
3
1.4
SPECIFICATIONS-----------------------------------------------------------------------------------------------------------------
3
SECTION 2 INSTALLATION AND
ACCEPTANCE-----------------------------------------------------------------------------13
2.1
UNPACKING-----------------------------------------------------------------------------------------------------------------------13
2.2 POWER
REQUIREMENTS.........................................................................................................................13
2.3 MECHANICAL
INSTALLATION..................................................................................................................13
2.4 INPUT
WIRING............................................................................................................................................13
2.5 OUTPUT
CONNECTIONS..........................................................................................................................20
2.6 OUTPUT VOLTAGE
RANGES....................................................................................................................20
2.7 FUNCTION
TEST.........................................................................................................................................20
2.8 REAR PANEL DIP SWITCH
(SW1)............................................................................................................21
SECTION 3
OPERATION----------------------------------------------------------------------------------------------------------------24
3.1
GENERAL--------------------------------------------------------------------------------------------------------------------------24
3.2 FRONT PANEL
CONTROLS-------------------------------------------------------------------------------------------------24
3.3 FRONT PANEL
INDICATORS------------------------------------------------------------------------------------------------24
3.4 REAR PANEL
CONNECTIONS----------------------------------------------------------------------------------------------26
3.5 FRONT PANEL
PROGRAMMING-------------------------------------------------------------------------------------------31
3.6 TO MEASURE THE
OUTPUT------------------------------------------------------------------------------------------------46
3.7 REMOTE PROGRAMMING WITH ABBREVIATED PLAIN ENGLISH
(APE)---------------------------------47
3.8 REMOTE OPERATION WITH MATE
CIIL--------------------------------------------------------------------------------67
SECTION 4 CALIBRATION
PROCEDURE-----------------------------------------------------------------------------------------82
4.1
GENERAL....................................................................................................................................................82
4.2 TEST
EQUIPMENT---------------------------------------------------------------------------------------------------------------83
4.3 PERIODIC
CALIBRATION------------------------------------------------------------------------------------------------------88
4.4 NONPERIODIC
CALIBRATION----------------------------------------------------------------------------------------------96
SECTION 5 THEORY OF
OPERATION--------------------------------------------------------------------------------------------105
5.1
GENERAL...................................................................................................................................................105
5.2 OVERALL
DESCRIPTION.........................................................................................................................105
5.3 INPUT POWER
SUPPLY..........................................................................................................................105
5.4 AUXILIARY POWER
SUPPLY..................................................................................................................107
5.5 CURRENT LIMIT
BOARD..........................................................................................................................107
5.6 INDICATOR
BOARD..................................................................................................................................107
5.7 RANGE RELAY
BOARD............................................................................................................................107
5.8 AMPLIFIER
MODULES.............................................................................................................................107
5.9 OSCILLATOR
MODULE............................................................................................................................108
5.10 CPU/GPIB
BOARD.....................................................................................................................................108
5.11 PHASE A/REF
BOARD..............................................................................................................................109
5.12 PHASE B/C
BOARD..................................................................................................................................109
5.13 DISPLAY
MODULE.....................................................................................................................................109
SECTION 6 MAINTENANCE AND
TROUBLESHOOTING-------------------------------------------------------------------111
6.1
GENERAL...................................................................................................................................................111
6.2 POOR VOLTAGE
ACCURACY----------------------------------------------------------------------------------------------111
6.3 POOR OUTPUT VOLTAGE
REGULATION..............................................................................................111
6.4 OVERTEMPERATURE LAMP
ON.............................................................................................................111
6.5 OVERLOAD LAMP
ON..............................................................................................................................112
6.6 CAN'T PROGRAM AC POWER SYSTEM ON
GPIB..............................................................................112
6.7 DISTORTED
OUTPUT..............................................................................................................................112
6.8 NO
OUTPUT-----------------------------------------------------------------------------------------------------------------------113
6.9 MODULE
REMOVAL------------------------------------------------------------------------------------------------------------113
6.10 OSCILLATOR MODULE
REMOVAL/REPLACEMENT...........................................................................113
6.11 AMPLIFIER
REMOVAL/REPLACEMENT................................................................................................114
SECTION 7 REPLACEABLE
PARTS-----------------------------------------------------------------------------------------------117
7.1
GENERAL...................................................................................................................................................117
7.2 ORDERING
INFORMATION.....................................................................................................................117
SECTION 8
MIL-STD-704D-------------------------------------------------------------------------------------------------------------119
8.1
GENERAL-------------------------------------------------------------------------------------------------------------------------119
8.2 INITIAL
SETUP--------------------------------------------------------------------------------------------------------------------119
8.3 TEST
PERFORMED------------------------------------------------------------------------------------------------------------119
8.4 KEYPAD ENTRY (Refer to page 31 for Keyboard flow
chart)...............................................................120
8.5 GPIB OPERATION (Refer to page 150 for syntax
diagram).................................................................122
8.6 TEST
SPECIFICATION.............................................................................................................................122
SECTION 9 2-PHASE OPTION
(2P)-------------------------------------------------------------------------------------------------135
9.1
GENERAL...................................................................................................................................................135
SECTION 10
RTCA/DO-160C---------------------------------------------------------------------------------------------------------137
10.1
GENERAL...................................................................................................................................................137
10.2 INITIAL
SETUP...........................................................................................................................................137
10.3 TEST
PERFORMED..................................................................................................................................137
10.4 KEYPAD ENTRY (Refer to Figure 1 for Keyboard Flow
Chart).............................................................137
10.5 GPIB
OPERATION.....................................................................................................................................139
10.6 TEST
SPECIFICATION.............................................................................................................................140
LIMITED
WARRANTY------------------------------------------------------------------------------------------------------------------------147
CaliforniaInstruments-7412-Manual-Page-1-Picture
Start Free Download


Comments

No comments yet.

Add Comment

* Required information
(never displayed)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
Enter the third letter of the word castle.
 
Enter answer:
 
Notify me of new comments via email.
 
Remember my form inputs on this computer.
 
 
Powered by Commentics