Equipment information:

California Instruments 1001TC Power supply
Manufacturer:
California Instruments
Model: 1001TC
Date: 1985
Category: Measurement instruments
Group: Power supply
Description: Power Source
Information:
                                    The California instruments Model 100ITC Power Amplifier is a
solid state, high performance, low distortion power source
that provides up to 1000 VA output when used with the proper
plug-in oscillator. The Model 1001TC Power Source is
illustrated in Figure 1-1. Full power output is available in
two different voltage ranges and over the frequency range
from 45 Hz to 5 KHz. These full power voltage ranges are:
1) 110 to 130 volts rms for normal single phase 115 volt
applications· and for three phase 208 to 225 volt
line-to-line applications.
2) 220 to 260 volts rms for normal single phase 230 volt
applications and for three phase 208 to 260 volt
applications where open delta operation is acceptable.
For two phase and three phase operation, at least two power
amplifiers must be combined together with the applicable
multi-phase oscillator. Two power amplifiers will provide a
total of 2000 VA two phase power (Model 20Ö0TC/2-2), or 2000
VA of three phase power (Model 2000TC/2-3D) in the open
delta configuration. Three power amplifiers will provide
3000 VA of three phase power in the wye configuration (Model
30Ö0TC/3-3).

These manuals are available for the above equipment:

California Instruments -- 1001TC -- Service Manual
File name: CaliforniaInstruments-7396-Manual-Page-1-Picture
Manual Type: Service Manual
Pages: 78
Size: 2.60 Mbytes (2724042 Bytes)
Language: english
Revision: revised
Manual-ID/Number:
Date: February 1985
Quality: Scanned document, reading partly badly, partly not readable.
Upload date:
MD5: 6efbf805b8bcf9b6ecb428c5d2bafb62
ed2kID: cbce1c40ebce402a279f65cf917f77eb
Downloads: 37 since 20 December 2015
Information:
This instruction manual contains information on the
installation, operation, calibration and maintenance of the
California Instruments Model 100 ITC Power Source. Detailed
schematics, parts location drawings, calibration procedures
and theory of operation are also contained for the aid of
maintenance personnel.

GENERAL DESCRIPTION PAGE
1. 1 INTRODUCTION 1
1. 2 general DESCRIPTION 1
1.3 ACCESSORY EQUIPMENT 1
INSTALLATION AND OPERATION
2. 1 UNPACKING 5 2. 2 POWER REQUIREMENTS 5 2. 3 CIRCUIT
BREAKER REQUIREMENTS 6
2.4 OUTPUT VOLTAGE RANGE AND 6 METER RANGE
2.5 ACCEPTANCE TEST PROCEDURE 6 2. 6 MECHANICAL INSTALLATION
8 2. 7 INPUT POWER WIRING 8 2. 8 OUTPUT POWER WIRING 8 2. 9
FRONT PANEL CONTROLS 8
2. 10 OPERATION OVER EXTENDED FREQUENCY 9
RANGE
THEORY OF OPERATION
3.1 GENERAL 11
3. 2 DETAILED CIRCUIT DESCRIPTION 11
CALIBRATION PROCEDURE
4. 1 GENERAL 18
4. 2 TEST EQUIPMENT REQUIRED 19
4. 3 INITIAL ADJUSTMENTS 19
4.4 AC LINE INPUT POWER AND OVERLOAD 21 ADJUSTMENT
4. 5 VOLTAGE, POWER OUTPUT AND HARMONIC 23 DISTORTION
4. 6 LINE REGULATION 23
4. 7 LOAD REGULATION ADJUSTMENT 25
4. 8 AMPLITUDE STABILITY 26
4. 9 FREQUENCY RESPONSE 26
4. 10 AC NOISE LEVEL 26
4. 11 0. 7 LAGGING POWER FACTOR 27
4. 12 0. 7 LEADING POWER FACTOR 28
Naintenance and Troubleshooting
5. 1 GENERAL
5. 2 TROUBLESHOOTING
CIRCUIT DIAGRAMS
6. 1 GENERAL
6. 2 REFERENCE DESIGNATIONS REPLACEABLE PARTS
7. 1 GENERAL
7. 2 ORDERING INFORMATION
PARTS LIST
APPENDIX A
CODE LIST OF MANUFACTURERS
CaliforniaInstruments-7396-Manual-Page-1-Picture
Start Free Download


Comments

No comments yet.

Add Comment

* Required information
(never displayed)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
Enter the third word of this sentence.
 
Enter answer:
 
Notify me of new comments via email.
 
Remember my form inputs on this computer.
 
 
Powered by Commentics