Equipment information:

Kikusui Electronics Corporation T0S 6200 Other
Kikusui Electronics Corporation
Model: T0S 6200
Date: 2000
Category: Measurement instruments
Group: Other
Description: Earth continuity Tester
                                    This tester is used to perform earth continuity tests
required for class-I devices for various safety standards,
including the IEC, EN, VDE, BS, JIS, UL, and the Electrical
Appliance and Material Control Law of Japan.
The tester must be used under the following conditions:
Test current value: 3A to 30 A AC Output terminal voltage:
5.4 V or less Resistance value: 1.2 Ω or less Maximum power:
150 VA or less
1. Making test current constant
The test current for earth continuity tests has been made
constant. This relieves the operator of the burdensome
procedure of resetting the test current when the resistance
of the DUT (Device Under Test) changes.
2. Safety output voltage
The constant current/constant voltage circuit provides fast
response, preventing generation of excessive output voltage
even when output is interrupted during testing. The tester
complies with the limitations on no-load output voltages (6
V or less, 12 V or less, and so on) required by many safety
4. Compact and lightweight
A new high-efficiency power supply (achieving a power
conversion efficiency of 65%) and large output (150 VA)
makes possible a tester that is remarkably compact and
lightweight, about half the size and weight of our
conventional testers.
5. Excellent measurement accuracy
The tester is equipped with an ammeter of +/-(1 % of reading
+ 0,2 A), a voltmeter of +/“(1 % of reading + 0.02V), and an
ohmmeter of +/-(2% of reading + 0.003 Ω) that calculates
resistance values based on measured current and voltage.
6. Offset canceling function
The tester has an offset canceling function that cancels
values for contact resistance at alligator-clip connections
or other connecting points, resistance components, and the
contact resistance of measuring leads in measurements using
two terminals.
7. Contact check function
The tester is provided with a contact check function that
verifies the connection of the DUT (by current detection)
before initiating testing.
8. Simple operations
Tester functions are fast and easily controlled, with an
intuitive control method that's easy to pick up, even for
first-time users.
For example, test conditions are set simply by selecting an
item displayed on the LCD with the cursor keys and turning
the rotary knob to set/select a value.
Function keys allow you to set shortcuts to a desired
setting item.
9. Stores up to 100 types of test conditions
The tester allows you to store and name up to 100 test
conditions involving parameters such as test current,
determined resistance value, and test time. For example, you
can store test conditions for a specific safety standard
under the name of the standard, or store test conditions
under the name of the destination of the DUT.
When test conditions need to be modified due to changes in
the destination of the product or revised safety standards,
you can recall a set of test conditions simply by entering a
memory number, making necessary modifications to the
pre-existing standard.
Assigning specific names allows test conditions to called up
by name. This function is available through both the front
panel and the remote control.
10. Programming of test conditions
A combination of stored test conditions allows automatic
execution of tests consisting of several programs of up to
100 steps each.
Although the total number of steps is limited to 500, 100
types of programs can be stored and recalled from the front
panel or the remote control.

These manuals are available for the above equipment:

Kikusui Electronics Corporation -- T0S 6200 -- User Manual
File name: Kikusi-7066-Manual-Page-1-Picture
Manual Type: User Manual
Pages: 158
Size: 9.56 Mbytes (10019546 Bytes)
Language: english
Manual-ID/Number: Z1-002-252, IB002615
Date: 2000
Quality: Scanned document, all readable.
Upload date:
MD5: 2b6b726c5bedd73fc4afd5e06185cbcb
ed2kID: 83e510d351b2ee63a94c7c7b20ca7665
Downloads: 69 since 14 August 2015
The contents of this operation manual are as follows:
Gives an overview of the tester and describes its features
and various options.
Chapter 1 Setup
Describes proper procedures for performing specific tasks,
from unpacking to installation to preparation required
before switching on POWER. Precautions for installing and
connecting the AC power cord are provided here. Read this
chapter before using the tester.
Chapter 2 Basic Operation
Describes basic operations such as setting test conditions
and starting a test.
Chapter 3 REMOTE and SIGNAL I/O
Describes the REMOTE terminal (for connecting optional
equipment) and the SIGNAL I/O connector (for input/output
Chapter 4 GPIB and RS-232C
Gives the device messages used to control the tester via a
GPIB or RS-232C interface.
Chapter 5 Part Names and Functions
Gives the names and functions of switches, connectors, and
other parts on the front and rear panels.
This chapter provides descriptions of the A(alert) symbols
located on tester panels.
Chapter 6 Maintenance
Explains tester maintenance, inspection, and calibration.
Chapter 7 Specifications
Provides tester specifications.
Explains basic tester principles; provides a table for ASCII
codes 20H to 7EH and excerpts from various earth continuity
test safety standards.
Start Free Download


No comments yet.

Add Comment

* Required information
(never displayed)
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
Enter the third word of this sentence.
Enter answer:
Notify me of new comments via email.
Remember my form inputs on this computer.
Powered by Commentics