Equipment information:

Philips PM5139 Generator
Manufacturer:
Philips
Model: PM5139
Date: 1997
Category: Measurement instruments
Group: Generator
Description: Function Generator 0.1 mHz - 20 MHz
Information:
                                    The PM5139 function generator introduces a new concept of
menu-driven operation to waveform generation and frequency
synthesis.
Microprocessor control enables simple and rapid operation
and allows you to set parameters by stepping through the
menu offered. One single control rotary knob allows you to
make precise settings of all numeric values.
The large backlit LCD clearly displays the selected signal
and gives a readout of vital parameters, such as frequency,
waveform, amplitude, and modulation. Any invalid parameter
selections are ignored and an error message shows the
incorrect settings that have been made.
The PM5139 frequency range covers IT/2 decades, from 0.1 mHz
to 20 MHz. Ten waveforms are selectable, including standard
functions, such as sine, triangle, square, as well as
positive and negative sawtooth, different pulses, and haversine.
Seven modulation modes are available:
• Amplitude modulation (AM)
• Frequency modulation (FM)
• Phase Shift Keying (PSK)
• GATE
• Linear SWEEP
• Logarithmic SWEEP
• BURST

The 10-key section on the right of the front panel permits a
versatile activation and control of such functions as single
or continuous sweep or burst, sweep hold, and switching from
internal to external modulation or trigger source; further
asymmetrical waveforms with variable duty cycle, key for
instant return to symmetrical waveform, store and recall
keys for up to nine complete instrument settings, a DIAL
LOCK key to disable the rotary control, and a key for
switching the signal output impedance.
AC or DC amplitudes can be precisely set using the numeric
setting rotary knob. DC offset is set independently of the
AC output amplitude. The output signals phase noise and
residual FM are very low, ensuring a clean and stable signal.
The instrument is optionally available under type number
PM5139/02 with a built-in GPIB (IEEE bus) interface and
under number PM5139/03 with built-in RS-232 interface. All
instrument functions can be remotely activated from a PC or
test system controller. It is also possible to upload
settings and status data from the instrument for storage in
the controller and later recall at any time. The facility
IEEE bus makes PM5139 an integral part of an automated test
system.
The PM5139 with interface also offers a user-definable
’’arbitrary” waveform ARB: the desired waveform may be
programmed on the PC, and than downloaded to the generator
via interface. Twenty-four arbitrary waveforms can be stored
separately.
A test program is built in to provide customer support and
to facilitate servicing.
The PM5139 is very much suited for applications in research
and development, production monitoring, quality assurance,
and for service purposes.

These manuals are available for the above equipment:

Philips -- PM5139 -- User Manual
File name: Philips-6936-Manual-Page-1-Picture
Manual Type: User Manual
Pages: 130
Size: 7.45 Mbytes (7806917 Bytes)
Language: english
Revision: Revised
Manual-ID/Number: 4822 872 10203
Date: February 1999
Quality: Electronic document, no scan, very well readable.
Upload date:
MD5: 6f75f1e5f7668c47535814a36e755ed6
ed2kID: 29f0dc8b1b33cabcb896985ee8fd9f8d
Downloads: 59 since 29 July 2015
Information:
1
INSTALLATION AND SAFETY INSTRUCTIONS
1 - 1
1.1
SAFETY INSTRUCTIONS
1 - 1
1.1.1
Maintenance and Repair
1 - 1
1.1.2
Grounding
1 - 1
1.1.3
Connections
1 - 2
1.1.4
Line Voltage Setting and Fuses
1 - 2
1.2
OPERATING POSITION OF THE INSTRUMENT
1 - 3
1.3
RADIO INTERFERENCE SUPPRESSION
1 - 3
2
MAIN CAPABILITIES
2 - 1
2.1
INTRODUCTION
2 - 1
3
OPERATING INSTRUCTIONS
3 - 1
3.1
GENERAL INFORMATION
3 - 1
3.2
TURNING THE INSTRUMENT ON
3 - 1
3.3
SELF-TEST ROUTINE
3 - 1
3.4
BRIEF CHECKING PROCEDURE
3-2
3.4.1
General Information
3-2
3.4.2
Functional Test
3-2
3.5
OPERATION
3-3
3.5.1
Design of Display Field and Keyboard
3-3
3.5.2
Control Elements, Display and Connectors
3-5
3.5.3
Keyboard Input
3-9
3.5.4
Frequency Setting
3-10
3.5.5
Setting Output Amplitude
3-12
3.5.6
Selection of the Signal Waveform
3-14
3.5.7
Modulation Modes
3-15
3.5.8
Store and Recall of Instrument Settings
3-24
3.5.9
Error Messages, Operating Errors
3-25
3.6
SPECIAL APPLICATION
3-26
3.7
REMOTE CONTROL OF THE INSTRUMENT
3-29
3.7.1
Introduction
3-29
3.7.2
IEEE-488 Interface
3-29
3.7.2.1
Instrument Address
3-30
37.2.2
Interface Functions
3-30
3.7.3
RS-232 Interface
3-31
3.7.3.1
Instrument Configuration
3-31
3.7.3.2
Interface Functions and Wiring
3-35
3.7.3.3
Special Interface Functions
3-37
3.7.4 Remote Control Commands
3-37
3.7.4.1 Program Message Syntax
3-37
3.7.4.2 Message Terminator
3-38
3.7.4.3 Service Request (SRQ) and Status Registers
3-38
3.7.4.4 Common Commands and Queries (IEEE-488.2)
3-40
3.7.4.5 Device-Specific Messages
3-43
3.7.4.6 Arbitrary Waveform (ARB)
3-48
3.7.5 Program Examples
3-52
3.7.6 Error Messages
3-59
3.7.7 Commands in Alphabetic Order
3-60
3.8.
TEST PROGRAM
3-63
4
CHARACTERISTICS
4 - 1
4.1
SAFETY AND EMC REQUIREMENTS
4 - 1
4.2
PERFORMANCE CHARACTERISTICS, SPECIFICATIONS
4 - 1
4.3
FREQUENCY, RESOLUTION
4 - 1
4.4
SYNCHRONIZATION
4-2
4.5
WAVEFORMS
4-2
4.6
WAVEFORM CHARACTERISTICS
4-3
4.6.1 Sine Wave
4-3
4.6.2 Square Wave and Rectangular Pulses
4-3
4.6.3 Triangle and Sawtooth
4-3
4.7
SIGNAL OUTPUT
4-4
4.8
MODULATION
4-5
4.8.1 Amplitude Modulation (AM)
4-6
4.8.2 Frequency Modulation (FM)
4-6
4.8.3 Phase Shift Keying (PSK)
4-7
4.8.4 Gate
4-7
4.8.5 Sweep
4-8
4.8.6 Burst
4-9
4.9
STORAGE AND RECALL OF INSTRUMENT SETTINGS
4-10
4.10
REMOTE CONTROL
4-10
4.10.1 IEEE-488 Interface (PM5139/02)
4-10
4.10.2 RS-232 Interface (PM5139/03)
4-11
4.10.3 Timing
4-11
4.10.4 Arbitrary Waveforms
4-11
4.11
CONNECTORS
4-13
4.12
ERROR MESSAGES
4-13
4.13
SELF-TEST ROUTINE, DIAGNOSTIC PROGRAM
4-13
4.14
POWER SUPPLY
4-14
4.15
ENVIRONMENTAL CONDITIONS
4-14
4.16
SAFETY- AND QUALITY DATA; CABINET
4-15
4.17
ACCESSORIES
4-15
4.17.1 Standard
4-15
4.17.2 Optional
4-15
5 PERFORMANCE TEST 5 -1
5.1 INTRODUCTION 5 - 1
5.2 RECOMMENDED TEST EQUIPMENT 5 - 1
5.3 SELF-TEST ROUTINE 5 - 1
5.4 PERFORMANCE VERIFICATION 5-2
5.4.1 Frequency 5-2
5.4.2 10 MHz Synchronization 5-3
5.4.3 Waveform Asymmetry 5-4
5.4.4 Sine Wave 5-4
5.4.5 Square Wave and Rectangular Pulses 5-7
5.4.6 AC Output Amplitude 5-9
5.4.7 DC Voltage 5-11
5.4.8 Modulation 5-12
5.4.9 TTL OUTPUT Level Test 5-18
Philips-6936-Manual-Page-1-Picture
Start Free Download


Comments

No comments yet.

Add Comment

* Required information
(never displayed)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
Enter the last letter of the word satellite.
 
Enter answer:
 
Notify me of new comments via email.
 
Remember my form inputs on this computer.
 
 
Powered by Commentics