Hewlett Packard 5382A Frequency counter
Manufacturer:
Image 1 of 2
Image 2 of 2
If you have any other photos or manuals for the
Hewlett Packard 5382A you can upload the files here .
Model:
5382A
Date:
1974
Category:
Group:
Description:
Information
The HP Model 5382A Frequency Counter (see Figure 1-1) is a
direct-counting frequency Counter that has a range of 10 Hz
to 225 MHz. Eight display digits are provided. Front-panel
controls allow a selection of gate times and attenuation
factors of the input signal. A rear-panel connector and
associated selector switch allow connection of an external
time base Oscillator. This feature also allows ratio
measurements to be made by the Counter. When the optional
temperature compensated crystal Oscillator is included
(Option 001), the switch is not provided and the connector
allows external use of the 10 MHz time base Oscillator.
Refer to Table 1-1 for all Counter specifications.
Manual type:
Service and User Manual
Pages:
34
Size:
4.98 Mbytes (5224281 Bytes)
Language:
english
Revision:
Manual ID:
05382-90001
Date:
1974 05 01
Quality:
Scanned document, reading partly badly, partly not readable.
Upload date:
2017 12 30
MD5:
3c296ca1e1894866ea39aeda4acd5dcf
Downloads:
553
Information
I GENERAL INFORMATION
... 1-1
1-1.
Introduction ... 1-1
1-3. Instrument Description
... 1-1
1-5. Instrument Identification
... 1-1
1-8. Specifications
... 1-2
II INSTALLATION AND OPERATION
... 2-1
2-1. Introduction
... 2-1
2-3. Unpacking and
Inspection ... 2-1
2-5. Storage and Shipment
... 2-1
2-8. Line Voltage
Selection ... 2-1
2-11. Operation
... 2-2
2-13. Cable and Termination
Requirements ... 2-2
2-15. Ratio Measurements (Standard Counter Only)
... 2-2
2-18. Optimizing Noise Rejection
... 2-2
III MAINTENANCE
... 3-1
3-1.
Introduction ... 3-1
3-3. Theory of Circuit Operation
... 3-1
3-5. Input Circuits
... 3-2
3-7. Decade Counter, Latch, and Multiplexer Circuits
... 3-2
3-9. Time Base Oscillator and Divider
... 3-2
3-14. Display
Scanner ... 3-2
3-17. Display Blanking Circuits
... 3-3
3-20. Reset and Transfer Control Circuits
... 3-3
3-22. Recommended Test Equipment
... 3-3
3-24. In-Cabinet Performance Check
... 3-4
3-26. Instrument
Access ... 3-4
3-28. Preventive Maintenance
... 3-6
3-30. General Repair
... 3-7
3-34. Adjustments
... 3-7
3-36. Amplifier Balance
Adjustment ... 3-7
3-38. Oscillator Adjustment (Standard Unit)
... 3-7
3-40. Oscillator Adjustment (Option 001 Unit)
... 3-8
3-42. Troubleshooting
... 3-8
3-45. Replaceable Parts
... 3-8
3-47. Ordering Information
... 3-10
3-49. Schematic Diagram
... 3-10
Manual type:
Service and User Manual
Pages:
43
Size:
7.57 Mbytes (7934741 Bytes)
Language:
english
Revision:
Manual ID:
05382-90001
Date:
Quality:
Electronic document, no scan, very well readable.
Upload date:
2015 05 30
MD5:
adc0e00653f409472390bb56c7b6b195
Downloads:
1070
Information
GENERAL INFORMATION
...
i”1
1-1.
Introduction ...
I-*
1-3. Instrument Description
...
I-1
1-5. Instrument Identification
...
1-8. Specifications
...
1“2
INSTALLATION AND OPERATION
... 2-1
2-1.
Introduction ...
2-1
2-3. Unpacking and
Inspection ...
2-1
2-5. Storage and
Shipment ...
2-1
2-8. Line Voltage
Selection ...
2-1
2-11. Operation
...
2-2
2-13. Cable and Termination
Requirements ... 2-2
2-15. Ratio Measurements (Standard Counter Only)
... 2-2
2-18. Optimizing Noise Rejection
...
2-2
MAINTENANCE
...
3-1
3-1.
Introduction ...
3-1
3-3. Theory of Circuit Operation
...
3-1
3-5. Input Circuits
...
3-2
3-7. Decade Counter, Latch, and Multiplexer Circuits
... 3-2
3-9. Time Base Oscillator and
Divider ... 3-2
3-14. Display
Scanner ...
3-2
3-17. Display Blanking Circuits
...
3-3
3-20. Reset and Transfer Control Circuits
... 3-3
3-22. Recommended Test Equipment
... 3-3
3-24. In-Cabinet Performance Check
... 3-4
3-26. Instrument
Access ...
3-4
3-28. Preventive Maintenance
...
3-6
3-30. General Repair
...
3-7
3-34. Adjustments
...
3-7
3-36. Amplifier Balance
Adjustment ...
3-7
3-38. Oscillator Adjustment (Standard
Unit) ... 3-7
3-40. Oscillator Adjustment (Option 001 Unit)
... 3-8
3-42. Troubleshooting
...
3_®
3-45. Replaceable Parts
...
3~®
3-47. Ordering Information
...
3-10
3-49. Schematic Diagram
...
3-10
Specifications
... 1-1
3-1. Recommended Test Equipment
... 3-4
3-2. In-Cabinet Performance Check
... 3-5
3-3. Replaceable Parts
...
3-12
3-4. Manufacturers Code List
...
3-15
3-5. Major Signal Definitions
...
3-17