Equipment information:

Fluke 123 ScopeMeter
Manufacturer:
Fluke
Model: 123
Date: 1997
Category: Measurement instruments
Group: ScopeMeter
Description: Industrial ScopeMeter
Information:
                                    Dual input oscilloscope
Vertical
Frequency response
DC coupled:
Excluding probes and test leads:
DC to 20 MHz (-3 dB)
With STL120 1:1 shielded test leads:
DC to 12.5 MHz (-3 dB)
DC to 20 MHz (-6 dB)
With PM 8918 10:1 probe (optional
accessory): DC to 20 MHz (-3 dB)
AC coupled (LF roll off)
Excluding probes and test leads:
<10 Hz (-3 dB)
With STL120: <10 Hz (-3 dB)
With PM 8918: <1 Hz (-3 dB)
Rise time
Excluding probes and test leads:
<17.5 ns
Input impedance
Excluding probes and test leads:
1 MW//12 pF
With BB120: 1 MW//20 pF
With STL120: 1 MW//225 pF
With PM 8918: 10 MW//15 pF
Sensitivity: 5 mV to 500V/div
Display modes: A, -A, B, -B
Max input voltage
A, B: 600V rms up to 200 kHz,
derating to 6V rms @ 20 MHz
Max floating voltage
From any terminal to ground:
600V rms up to 400 Hz
Resolution: 8 bit
Vertical accuracy: ±(1% of reading
+ 0.05 range/div)
Max vertical move: ±4 divisions
Horizontal
Acquisition modes
Normal: Equivalent sampling: 20 ns
to 500 ns/div; real time sampling:
1 ms to 5s/div
Single (real time): 1 ms to 5s/div
Roll (real time): 1s to 60s/div
Sampling rate (for both channels
simultaneously): For repetitive
signals (equivalent sampling) up to
1.25 GS/s; real time (normal and
single): 1 ms to 5 ms/div, 25 MS/s;
10 ms to 5s/div, 5 MS/s
Time base accuracy
Equivalent sampling: ±(0.4%
of reading +0.04 time/div)
Real time sampling: ±(0.1%
of reading +0.04 time/div)
Glitch detection: ³40 ns
@ 20 ns to 5 ms/div; ³200 ns
@ 10 ms to 5s/div
Glitch detection is always active
Horizontal move, 10 divisions.
Permits shifting of the display
from 0 to 10 division of pre-trigger.
Trigger point will always be visible.

These manuals are available for the above equipment:

Fluke -- 123 -- Service Manual
File name: Fluke-6525-Manual-Page-1-Picture
Manual Type: Service Manual
Pages: 170
Size: 5.26 Mbytes (5519764 Bytes)
Language: english
Revision: 3
Manual-ID/Number: 4822 872 05375
Date: January 2000
Quality: Electronic document, no scan, very well readable.
Upload date:
MD5: d1e4ef72a9bc1d3fa26a274826207797
ed2kID: a9a40a38ef66b804d33338e1ff1d2d38
Downloads: 80 since 29 November 2014
Information:
1 Safety Instructions
.............................................................................
1-1
1.1
Introduction.................................................................................................
1-3
1.2 Safety
Precautions.......................................................................................
1-3
1.3 Caution and Warning
Statements................................................................
1-3
1.4
Symbols.......................................................................................................
1-3
1.5 Impaired Safety
...........................................................................................
1-4
1.6 General Safety
Information.........................................................................
1-4
2 Characteristics
...................................................................................
2-1
2.1
Introduction.................................................................................................
2-3
2.2 Dual Input
Oscilloscope..............................................................................
2-3
2.2.1 Vertical
................................................................................................
2-3
2.2.2 Horizontal
............................................................................................
2-4
2.2.3 Trigger
.................................................................................................
2-4
2.2.4 Advanced Scope
Functions..................................................................
2-5
2.3 Dual Input
Meter.........................................................................................
2-5
2.3.1 Input A and Input B
.............................................................................
2-5
2.3.2 Input A
.................................................................................................
2-8
2.3.3 Advanced Meter
Functions..................................................................
2-8
2.4 Miscellaneous
.............................................................................................
2-9
2.5 Environmental
.............................................................................................
2-10
2.6 Service and Maintenance
............................................................................
2-11
2.7 Safety
..........................................................................................................
2-11
2.8 EMC Immunity
...........................................................................................
2-12
3 Circuit Descriptions
...........................................................................
3-1
3.1
Introduction.................................................................................................
3-3
3.2 Block Diagram
............................................................................................
3-3
3.2.1 Channel A, Channel B Measurement
Circuits..................................... 3-4
3.2.2 Trigger Circuit
.....................................................................................
3-4
3.2.3 Digital Circuit
......................................................................................
3-5
3.2.4 Power Circuit
.......................................................................................
3-6
3.2.5 Start-up Sequence, Operating Modes
.................................................. 3-7
3.3 Detailed Circuit
Descriptions......................................................................
3-9
3.3.1 Power Circuit
.......................................................................................
3-9
3.3.2 Channel A - Channel B Measurement Circuits
................................... 3-15
3.3.3 Trigger Circuit
.....................................................................................
3-20
3.3.4 Digital Circuit
......................................................................................
3-25
4 Performance
Verification...................................................................
4-1
4.1
Introduction.................................................................................................
4-3
4.2 Equipment Required For Verification
........................................................ 4-3
4.3 How To
Verify............................................................................................
4-3
4.4 Display and Backlight Test
.........................................................................
4-4
4.5 Input A and Input B Tests
...........................................................................
4-5
4.5.1 Input A and B Base Line Jump
Test.................................................... 4-6
4.5.2 Input A Trigger Sensitivity Test
.......................................................... 4-7
4.5.3 Input A Frequency Response Upper Transition Point
Test................. 4-8
4.5.4 Input A Frequency Measurement Accuracy Test
................................ 4-8
4.5.5 Input B Frequency Measurement Accuracy Test
................................ 4-9
4.5.6 Input B Frequency Response Upper Transition Point Test
................. 4-10
4.5.7 Input B Trigger Sensitivity Test
.......................................................... 4-10
4.5.8 Input A and B Trigger Level and Trigger Slope
Test.......................... 4-11
4.5.9 Input A and B DC Voltage Accuracy Test
.......................................... 4-14
4.5.10 Input A and B AC Voltage Accuracy Test
........................................ 4-15
4.5.11 Input A and B AC Input Coupling
Test............................................. 4-16
4.5.12 Input A and B Volts Peak Measurements
Test.................................. 4-17
4.5.13 Input A and B Phase Measurements Test
.......................................... 4-18
4.5.14 Input A and B High Voltage AC/DC Accuracy
Test......................... 4-19
4.5.15 Resistance Measurements
Test..........................................................
4-20
4.5.16 Continuity Function Test
...................................................................
4-21
4.5.17 Diode Test Function Test
..................................................................
4-22
4.5.18 Capacitance Measurements Test
....................................................... 4-22
4.5.19 Video Trigger
Test.............................................................................
4-23
5 Calibration Adjustment
......................................................................
5-1
5.1 General
........................................................................................................
5-3
5.1.1
Introduction..........................................................................................
5-3
5.1.2 Calibration number and
date................................................................
5-3
5.1.3 General
Instructions.............................................................................
5-3
5.2 Equipment Required For
Calibration..........................................................
5-4
5.3 Starting Calibration Adjustment
.................................................................
5-4
5.4 Contrast Calibration Adjustment
................................................................
5-6
5.5 Warming Up & Pre-Calibration
..................................................................
5-7
5.6 Final Calibration
.........................................................................................
5-7
5.6.1 HF Gain Input A&B
............................................................................
5-7
5.6.2 Delta T Gain, Trigger Delay Time & Pulse Adjust Input
A................ 5-9
5.6.3 Pulse Adjust Input A (firmware V01.00 only)
.................................... 5-10
5.6.4 Pulse Adjust Input
B............................................................................
5-11
5.6.5 Gain DMM (Gain
Volt).......................................................................
5-11
5.6.6 Volt
Zero..............................................................................................
5-13
5.6.7 Zero Ohm (firmware V01.00
only)...................................................... 5-13
5.6.8 Gain
Ohm.............................................................................................
5-14
5.6.9 Capacitance Gain Low and
High......................................................... 5-15
5.6.10 Capacitance Clamp &
Zero................................................................
5-15
5.6.11 Capacitance
Gain...............................................................................
5-16
5.7 Save Calibration Data and
Exit...................................................................
5-16
6 Disassembling the Test Tool
............................................................. 6-1
6.1.
Introduction................................................................................................
6-3
6.2. Disassembling Procedures
.........................................................................
6-3
6.1.1 Required Tools
....................................................................................
6-3
6.2.2 Removing the Battery Pack
.................................................................
6-3
6.2.3 Removing the Bail
...............................................................................
6-3
6.2.4 Opening the Test Tool
.........................................................................
6-3
6.2.5 Removing the Main PCA
Unit.............................................................
6-5
6.2.6 Removing the Display
Assembly.........................................................
6-6
6.2.7 Removing the Keypad and Keypad
Foil.............................................. 6-6
6.3 Disassembling the Main PCA
Unit.............................................................
6-6
6.4 Reassembling the Main PCA Unit
..............................................................
6-8
6.5 Reassembling the Test
Tool........................................................................
6-8
7 Corrective Maintenance
.....................................................................
7-1
7.1
Introduction.................................................................................................
7-3
7.2 Starting Fault Finding.
................................................................................
7-4
7.3 Charger
Circuit............................................................................................
7-4
7.4 Starting with a Dead Test Tool
...................................................................
7-6
7.4.1 Test Tool Completely
Dead.................................................................
7-6
7.4.2 Test Tool Software Does not Run.
...................................................... 7-7
7.4.3 Software Runs, Test Tool not Operative
............................................. 7-7
7.5 Miscellaneous
Functions.............................................................................
7-8
7.5.1 Display and Back Light
.......................................................................
7-8
7.5.2 Fly Back
Converter..............................................................................
7-9
7.5.3 Slow
ADC............................................................................................
7-10
7.5.4
Keyboard..............................................................................................
7-11
7.5.5 Optical Port (Serial RS232
Interface)..................................................
7-11
7.5.6 Channel A, Channel B Voltage Measurements
................................... 7-12
7.5.7 Channel A Ohms and Capacitance
Measurements.............................. 7-13
7.5.8 Trigger
Functions.................................................................................
7-14
7.5.9 Reference
Voltages..............................................................................
7-15
7.5.10 Buzzer
Circuit....................................................................................
7-15
7.5.11 Reset ROM Circuit (PCB version <8
only)....................................... 7-16
7.5.12 RAM Test
..........................................................................................
7-16
7.5.13 Power
ON/OFF..................................................................................
7-16
7.5.14 PWM
Circuit......................................................................................
7-17
7.5.15 Randomize Circuit
.............................................................................
7-17
7.6 Loading
Software........................................................................................
7-17
8 List of Replaceable
Parts...................................................................
8-1
8.1
Introduction.................................................................................................
8-3
8.2 How to Obtain
Parts....................................................................................
8-3
8.3 Final Assembly Parts
..................................................................................
8-4
8.4 Main PCA Unit Parts
..................................................................................
8-6
8.5 Main PCA Parts
..........................................................................................
8-7
8.6 Accessory Replacement Parts
.....................................................................
8-24
8.7 Service
Tools...............................................................................................
8-24
9 Circuit
Diagrams.................................................................................
9-1
9.1
Introduction.................................................................................................
9-3
9.2 Schematic
Diagrams....................................................................................
9-4
10 Modifications
......................................................................................
10-1
10.1 Software modifications
.............................................................................
10-1
10.2 Hardware
modifications............................................................................
10-1
Fluke-6525-Manual-Page-1-Picture
Start Free Download


Fluke -- 123 -- Service Manual
File name: Fluke-6533-Manual-Page-1-Picture
Manual Type: Service Manual
Pages: 96
Size: 1.99 Mbytes (2082892 Bytes)
Language: english
Revision:
Manual-ID/Number: 4822 872 05398
Date: March 2007
Quality: Electronic document, no scan, very well readable.
Upload date:
MD5: c87ad484e83e45f4a08037ec9a5bb2fb
ed2kID: 484d5dce870dad72ca3a57d804ed0bde
Downloads: 149 since 29 November 2014
Information:
Limited Warranty & Limitation of
Liability........................................................
ii
Introduction and Safety
Instructions................................................................1-1
1.1 Introduction to Service Manual
.....................................................................
1-3
1.2 Safety
.............................................................................................................
1-3
1.2.1
Introduction.................................................................................................
1-3
1.2.2 Safety
Precautions.......................................................................................
1-3
1.2.3 Caution and Warning
Statements................................................................
1-3
1.2.4 Symbols used in this Manual and on Instrument
........................................ 1-4
1.2.5 Impaired
Safety...........................................................................................
1-4
1.2.6 General Safety
Information.........................................................................
1-4
Characteristics
...................................................................................................2-1
2.1
Introduction....................................................................................................
2-3
2.2 Dual Input
Oscilloscope.................................................................................
2-3
2.2.1
Vertical........................................................................................................
2-3
2.2.2 Horizontal
...................................................................................................
2-4
2.2.3 Trigger
........................................................................................................
2-4
2.2.4 Advanced Scope
Functions.........................................................................
2-5
2.3 Dual Input
Meter............................................................................................
2-5
2.3.1 Input A and Input B
....................................................................................
2-5
2.3.2 Input A
........................................................................................................
2-8
2.3.3 Advanced Meter Functions
.........................................................................
2-9
2.4 Cursor Readout (Fluke 124,
125)...................................................................
2-10
2.5 Harmonics Measurements (Fluke
125)..........................................................
2-10
2.6 Field Bus Measurements (Fluke 125)
............................................................
2-11
2.7 Miscellaneous
................................................................................................
2-11
2.8
Environmental................................................................................................
2-12
2.9 Service and Maintenance
...............................................................................
2-13
2.10 Safety
...........................................................................................................
2-13
2.11 EMC Immunity
............................................................................................
2-15
Performance
Verification...................................................................................3-1
3.1
Introduction....................................................................................................
3-3
3.2 Equipment Required For Verification
........................................................... 3-3
3.3 How To
Verify...............................................................................................
3-4
3.4 Display and Backlight
Test............................................................................
3-4
3.5 Input A and Input B
Tests..............................................................................
3-5
3.5.1 Input A and B Base Line Jump Test
........................................................... 3-6
3.5.2 Input A Trigger Sensitivity Test
.................................................................
3-8
3.5.3 Input A Frequency Response Upper Transition Point Test
........................ 3-9
3.5.4 Input A Frequency Measurement Accuracy Test
....................................... 3-9
3.5.5 Input B Frequency Measurement Accuracy
Test........................................ 3-10
3.5.6 Input B Frequency Response Upper Transition Point
Test......................... 3-11
3.5.7 Input B Trigger Sensitivity Test
.................................................................
3-12
3.5.8 Input A and B Trigger Level and Trigger Slope Test
................................. 3-13
3.5.9 Input A and B DC Voltage Accuracy Test
................................................. 3-16
3.5.10 Input A and B AC Voltage Accuracy Test
............................................... 3-18
3.5.11 Input A and B AC Input Coupling Test
.................................................... 3-19
3.5.12 Input A and B Volts Peak Measurements Test
......................................... 3-20
3.5.13 Input A and B Phase Measurements Test
................................................. 3-21
3.5.14 Harmonics (Fluke 125)
.............................................................................
3-21
3.5.15 Input A and B High Voltage AC/DC Accuracy
Test................................ 3-22
3.5.16 Resistance Measurements Test
.................................................................
3-24
3.5.17 Continuity Function Test
..........................................................................
3-25
3.5.18 Diode Test Function
Test..........................................................................
3-26
3.5.19 Capacitance Measurements
Test...............................................................
3-26
3.5.20 Video Trigger
Test....................................................................................
3-27
Calibration
Adjustment......................................................................................4-1
4.1
General...........................................................................................................
4-3
4.1.1
Introduction.................................................................................................
4-3
4.1.2 Calibration number and
date.......................................................................
4-3
4.1.3 General
Instructions....................................................................................
4-3
4.2 Equipment Required For
Calibration.............................................................
4-4
4.3 Starting Calibration Adjustment
....................................................................
4-4
4.4 Contrast Calibration Adjustment
...................................................................
4-6
4.5 Warming Up &
Pre-Calibration.....................................................................
4-7
4.6 Final Calibration
............................................................................................
4-7
4.6.1 HF Gain Input A&B
...................................................................................
4-7
4.6.2 Delta T Gain, Trigger Delay Time & Pulse Adjust Input
A ....................... 4-9
4.6.3 Pulse Adjust Input B
...................................................................................
4-10
4.6.4 Gain DMM (Gain Volt)
..............................................................................
4-10
4.6.5 Volt
Zero.....................................................................................................
4-12
4.6.6 Zero
Ohm....................................................................................................
4-12
4.6.7 Gain
Ohm....................................................................................................
4-13
4.6.8 Capacitance Gain Low and High
................................................................
4-14
4.6.9 Capacitance Clamp &
Zero.........................................................................
4-14
4.6.10 Capacitance Gain
......................................................................................
4-15
4.7 Save Calibration Data and
Exit......................................................................
4-15
Disassembling the Test Tool
............................................................................5-1
5.1.
Introduction...................................................................................................
5-3
5.2. Disassembling Procedures
............................................................................
5-3
5.1.1 Required
Tools............................................................................................
5-3
5.2.2 Removing the Battery Pack
........................................................................
5-3
5.2.3 Removing the Bail
......................................................................................
5-3
5.2.4 Opening the Test Tool
................................................................................
5-3
5.2.5 Removing the Main PCA
Unit....................................................................
5-5
5.2.6 Removing the Display
Assembly................................................................
5-6
5.2.7 Removing the Keypad and Keypad Foil
..................................................... 5-6
5.3 Disassembling the Main PCA
Unit................................................................
5-6
5.4 Reassembling the Main PCA
Unit.................................................................
5-8
5.5 Reassembling the Test
Tool...........................................................................
5-8
List of Replaceable Parts
..................................................................................6-1
6.1
Introduction....................................................................................................
6-3
6.2 How to Obtain
Parts.......................................................................................
6-3
6.3 Service Centers
..............................................................................................
6-3
6.4 Final Assembly Parts
.....................................................................................
6-4
6.5 Main PCA Unit Parts
.....................................................................................
6-6
6.6 Service Tools
.................................................................................................
6-7
Fluke-6533-Manual-Page-1-Picture
Start Free Download


Fluke -- 123 -- Datasheet
File name: Fluke-6539-Manual-Page-1-Picture
Manual Type: Datasheet
Pages: 4
Size: 729.75 Kbytes (747266 Bytes)
Language: english
Revision: A
Manual-ID/Number: J0661
Date: March 1997
Quality: Electronic document, no scan, very well readable.
Upload date:
MD5: 7d2cac54627692048572f02481b27222
ed2kID: 84cd1ba27d6105543fecb776e279e2a0
Downloads: 78 since 30 November 2014
Information:
Fluke-6539-Manual-Page-1-Picture
Start Free Download


Fluke -- 123 -- User Manual
File name: Fluke-7596-Manual-Page-1-Picture
Manual Type: User Manual
Pages: 83
Size: 1.84 Mbytes (1933945 Bytes)
Language: english
Revision:
Manual-ID/Number:
Date: September 2002
Quality: Electronic document, no scan, very well readable.
Upload date:
MD5: 06bfdf8754072d733a7d08576f198abd
ed2kID: 9fb0464b17d0bbb6e9174bedd345fc40
Downloads: 28 since 26 January 2016
Information:
Declaration of Conformity
.......................................................................................................
1
Unpacking the Test Tool Kit
...........................................................................................
2
Safely Using the Test Tool
.............................................................................................
4
1 Using The Test
Tool.....................................................................................................
7
Goal of this Chapter
.......................................................................................................
7
Powering the Test Tool
..................................................................................................
7
Resetting the Test Tool
..................................................................................................
8
Changing Backlight
........................................................................................................
9
Reading the Screen
.......................................................................................................
10
Making Selections in a Menu
.........................................................................................
11
Looking at the Measurement
Connections.....................................................................
12
Displaying an Unknown Signal with Connect-and View™
............................................. 13
Making
Measurements...................................................................................................
14
Freezing the
Screen.......................................................................................................
16
Holding a Stable Reading
..............................................................................................
16
Making Relative
Measurements.....................................................................................
17
Selecting Auto/Manual
Ranges......................................................................................
18
Changing the Graphic Representation on the Screen
................................................... 18
TrendPlotting a Waveform
.............................................................................................
22
Acquiring the Waveform
................................................................................................
23
Triggering on a Waveform
.............................................................................................
27
Saving and Recalling a Setup and a Screen
.................................................................
32
Making Cursor
Measurements.......................................................................................
35
Using the 10:1 Probe for High Frequency
Measurements............................................. 38
Using a Printer
...............................................................................................................
39
Using FlukeView® Software
...........................................................................................
41
2 Maintaining the Test
Tool............................................................................................
43
About this Chapter
.........................................................................................................
43
Cleaning the Test
Tool...................................................................................................
43
Storing the Test
Tool......................................................................................................
43
Charging the Rechargeable Battery
Pack......................................................................
44
Keeping Batteries in Optimal Condition
.........................................................................
45
Replacing and Disposing of the Rechargeable Battery Pack
........................................ 46
Using and Adjusting 10:1 Scope Probes
.......................................................................
47
Calibrating the Test
Tool................................................................................................
49
Parts and Accessories
...................................................................................................
49
3 Tips and
Troubleshooting...........................................................................................
53
Goal of this Chapter
.......................................................................................................
53
Using the Tilt
Stand........................................................................................................
53
Resetting the Test Tool
..................................................................................................
54
Changing the Information
Language..............................................................................
54
Changing the
Display.....................................................................................................
55
Changing Date and Time
...............................................................................................
56
Saving Battery Life
.........................................................................................................
57
Changing the Auto Set
Options......................................................................................
58
Using Proper Grounding
................................................................................................
59
Solving Printing and Other Communication Errors
........................................................ 60
Battery Testing of Fluke
Accessories.............................................................................
60
4
Specifications...............................................................................................................
61
Introduction
....................................................................................................................
61
Dual Input Oscilloscope
.................................................................................................
62
Dual Input
Meter.............................................................................................................
65
Cursor readout (Fluke 124)
............................................................................................
68
Miscellaneous
................................................................................................................
69
Environmental
................................................................................................................
70
Safety
......................................................................................................................
70
Fluke-7596-Manual-Page-1-Picture
Start Free Download


Fluke -- 123 -- Service Manual
File name: Fluke-7597-Manual-Page-1-Picture
Manual Type: Service Manual
Pages: 77
Size: 1.62 Mbytes (1697807 Bytes)
Language: english
Revision: 4
Manual-ID/Number: 4822 872 00743
Date: July 1999
Quality: Electronic document, no scan, very well readable.
Upload date:
MD5: 39798c0a31354b1504bed94ce32f6d3c
ed2kID: bb9093b4e73f2f5baeb62872cc48aaa1
Downloads: 21 since 26 January 2016
Information:
Declaration of Conformity
..............................................................................................
1
Unpacking the Test Tool Kit
..........................................................................................
2
Safely Using the Test Tool
............................................................................................
4
1 Using The Test Tool
....................................................................................................
7
Goal of this
Chapter.......................................................................................................
7
Powering the Test
Tool..................................................................................................
7
Resetting the Test Tool
.................................................................................................
8
Changing
Backlight........................................................................................................
9
Reading the
Screen.......................................................................................................
10
Making Selections in a
Menu.........................................................................................
11
Looking at the Measurement Connections
....................................................................
12
Input A
......................................................................................................................
12
Input B
......................................................................................................................
12
COM
........................................................................................................................
12
Displaying an Unknown Signal with Connect-and-View™
............................................. 13
Making Measurements
...................................................................................................
14
Freezing the Screen
.......................................................................................................
16
Holding a Stable Reading
..............................................................................................
16
Making Relative Measurements
.....................................................................................
17
Selecting Auto/Manual Ranges
......................................................................................
18
Changing the Graphic Representation on the Screen
.................................................... 18
Changing the Amplitude
............................................................................................
18
Changing the Time Base
...........................................................................................
18
Positioning the Waveform on the Screen
..................................................................
19
Smoothing the Waveform
..........................................................................................
20
Displaying the Envelope of a Waveform
....................................................................
21
TrendPlotting a
Waveform..............................................................................................
22
Starting a TrendPlot™ function
.................................................................................
22
Changing the TrendPlot Reading
..............................................................................
23
Turning Off the TrendPlot Display
.............................................................................
23
Acquiring the Waveform
.................................................................................................
23
Making a Single
Acquisition.......................................................................................
23
Recording Slow Signals over a Long Period of Time
................................................ 25
Selecting AC-Coupling
..............................................................................................
26
Reversing the Polarity of the Displayed Waveform
................................................... 26
Triggering on a Waveform
..............................................................................................
27
Setting Trigger Level and Slope
................................................................................
27
Selecting the Trigger Parameters
..............................................................................
28
Isolated
Triggering.....................................................................................................
29
Triggering on Video Signals
......................................................................................
29
Triggering on a Specific Video Line
..........................................................................
31
Saving and Recalling a Setup or a Screen
....................................................................
32
Saving
Screens.........................................................................................................
32
Recalling
Screens.....................................................................................................
33
Deleting Screens
......................................................................................................
33
Using a
Printer...............................................................................................................
34
Using FlukeView® Software
...........................................................................................
36
2 Maintaining the Test Tool
...........................................................................................
37
About this
Chapter.........................................................................................................
37
Cleaning the Test Tool
..................................................................................................
37
Storing the Test Tool
.....................................................................................................
37
Charging the Ni-Cd Battery Pack
..................................................................................
38
Keeping Batteries in Optimal Condition
.........................................................................
39
Replacing and Disposing of the Ni-Cd Battery Pack
..................................................... 40
Using and Adjusting 10:1 Scope Probes
.......................................................................
41
Calibrating the Test Tool
...............................................................................................
43
Parts and
Accessories...................................................................................................
43
Service Manual
.........................................................................................................
43
Standard
Accessories...............................................................................................
43
Optional Accessories
................................................................................................
46
3 Tips and Troubleshooting
..........................................................................................
47
Goal of this
Chapter.......................................................................................................
47
Using the Tilt Stand
.......................................................................................................
47
Resetting the Test Tool
.................................................................................................
48
Changing the Information Language
.............................................................................
48
Changing the Display
....................................................................................................
49
Adjusting the Screen Contrast
..................................................................................
49
Setting the Grid Display
.............................................................................................
49
Changing Date and Time
...............................................................................................
50
Saving Battery Life
.........................................................................................................
51
Setting the Power Down Timer
..................................................................................
51
Changing the Auto Set Options
......................................................................................
52
Using Proper
Grounding.................................................................................................
53
Solving Printing and Other Communication Errors
......................................................... 54
4 Specifications
...............................................................................................................
55
Introduction
....................................................................................................................
55
Dual Input
Oscilloscope..................................................................................................
56
Vertical.......................................................................................................................
56
Horizontal
..................................................................................................................
57
Trigger
.......................................................................................................................
57
Advanced Scope Functions
.......................................................................................
58
Dual Input
Meter.............................................................................................................
59
Input A and Input
B....................................................................................................
59
Input A
.......................................................................................................................
60
Advanced Meter Functions
........................................................................................
61
Miscellaneous.................................................................................................................
62
Environmental
................................................................................................................
63
Safety
.............................................................................................................................
64
Fluke-7597-Manual-Page-1-Picture
Start Free Download


Comments

No comments yet.

Add Comment

* Required information
(never displayed)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
Type the word for the number 9.
 
Enter answer:
 
Notify me of new comments via email.
 
Remember my form inputs on this computer.
 
 
Powered by Commentics