Geräte Informationen:

Gould K100-D Logic Analysator
Modell: K100-D
Datum: 1980
Kategorie: Messgeräte
Gruppe: Logic Analysator
Beschreibung: Digital Logic Analyzer
                                    The Model K100-D Logic Analyzer was designed to provide
the utmost in performance and versatility for the digital
designer and troubleshooter; i.e., it can be considered
to be a true benchmark tool. It serves as both a time
domain (data recorded asynchronously), and a data domain
analysis tool (data recorded synchronously). The unit
accepts up to 16 logic signals through its active input
probes, and stores these discriminated signals in its
1024 word memory, at sample rates to 100 MHz.

The Model K100-D has comprehensive recording and
display analysis capabilities that enable the user
to perform complex timing and state analysis of his
digital systems. The unit has three distinct features
that make it a useful tool for logic troubleshooting.

First, the signals from the user's system are input
via specially designed hybrid active probes. The input
impedance of each probe is 1 MΩ , 5 pF. The probes
are individual to allow spanning to physically separated
points in the system, and also to provide for convenient
connection at the PC board level. Signal conditioning,
or threshold detection, and buffering of a particular
signal is provided at a point as close as possible to
the user's circuitry. The probe tip, with its accessories,
allows convenient connection to a system. The probes
detect logic spikes or glitches down to 5 ns regardless
of clock rate used.

Second, the instrument can clock at rates to 100 MHz
allowing timing measurements on up to 16 signals,
with a 10 ns time resolution. A relatively long memory,
1024 words, allows precise timing measurements over longer
intervals of time. The performance of the active probes
complement this high-speed recording capability.

Third, the instrument uses a microprocessor linked
to a front keyboard for instrument control. Comprehensive
display prompting is used to make it easy to set up
the unit for desired recording and display formats.

Folgende Anleitungen sind hier verfügbar:

Dokumenttyp: Service- und Bedienungsanleitung Gould-4210-Manual-Page-1-Picture
Seitenanzahl: 155
Dateigröße: 10.20 Mbytes (10698838 Bytes)
Sprache: Englisch
Dokument-ID/Nummer: 0112-0102
Datum: 15 Februar 1980
Qualität: Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
MD5: af4c446e18f74d7f5f73f25351725010
Downloads: 221 seit dem 11 März 2013
General Information
1.1	Certification	1
1.2	Warranty	1
1.3	Description	1
1.4	Specifications	3
2.1	Introduction	5
2.2	Unpacking and Inspection	5
2.3	Storage and Shipment	5
2.4	Power Connection	5
2.5	Preparation for Use	5
2.6	Initial Warm-up	6
3.1	Introduction	8
3.2	Front Panel Controls and Inputs	8
3.3	Rear Panel Inputs and Outputs	20
3.4	Set-up Procedure and	21

Principles of Operation
4.1	Introduction	26
4.2	Basic General Description	26
4.3	Detailed Description	29
4.4	Front End	41
4.5	Record Control	48
4.6	Record Memory	58
4.7	Threshold	64
4.8	Front Panel and Keyboard	67
4.9	Probes	67
4.10	Regulator	69
4.11	CRT Display	70
Calibration Procedures		
5.1	Recalibration of Internal Circuits	74
5.2	Required Test Equipment	74
5.3	Calibration of Raster Scan Display	74
5.4	Power Supply Adjustments	77
5.5	Threshold Adjustments	77
5.6	Record Memory Adjustments	78
5.7	Special Precautions	80
6.1	Introduction	81
6.2	Diagnostic Routine and Indications	81
6.3	Required Test Equipment	87
6.4	Diagnostic and Troubleshooting
        Procedures	87

Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
Captcha Image
Powered by Commentics