Quadtech Inc. 1320 Netzteil
Hersteller:
Modell:
1320
Datum:
2001
Kategorie:
Gruppe:
Beschreibung:
Bias Current Source
Bedienungsanleitung
Dokumenttyp:
Bedienungsanleitung
Seiten:
81
Größe:
464.45 Kbytes (475592 Bytes)
Sprache:
english
Revision:
Dokument-ID:
150414/A2
Datum:
2001 03 01
Qualität:
Elektronisches Dokument, kein Scan, sehr gut lesbar.
Upload Datum:
2017 01 29
MD5:
84fc697e6c02daed635ff9eb2c3db84e
Downloads:
560

Information

Warranty ... 5 Specifications ... 7 Accessories ... 9 Safety Precautions ... 11 Condensed Operating Instructions ... 13 Introduction - Section 1 1.1 Unpacking and Inspection ... 15 1.2 Product Overview ... 15 1.3 Controls and Indicators ... 16 1.3.1 Front Panel Controls and Indicators ... 16 1.3.2 Rear Panel Controls and Connectors ... 19 1.4 Installation ... 20 1.4.1 Dimensions ... 20 1.4.2 Instrument Positioning ... 20 1.4.3 Power Requirements ... 21 1.4.4 Safety Inspection ... 22 Operation - Section 2 2.1 Terms and Conventions ... 23 2.2 System Parameters ... 26 2.2.1 Shift ... 27 2.2.2 I/F (Interface) ... 27 2.2.3 I (Current) ... 28 2.2.4 Mode ... 29 2.2.5 Address ... 34 2.2.6 Clock ... 34 2.2.7 Timer ... 35 2.2.8 Delay Time ... 36 2.2.9 Step Number ... 37 2.2.10 Loop ... 38 2.2.11 Local ... 38 2.2.12 Prog/Esc ... 39 2.2.13 Store ... 40 2.2.14 Recall ... 41 2.2.15 Clear ... 41 2.2.16 B.S. (Backspace) ... 42 2.2.17 Enter ... 42 2.2.18 DCV Display ... 42 2.2.19 BIAS/DCR ... 43 2.2.20 FWD/REV ... 43 2.3 Start-Up ... 44 2.4 Zero Function ... 44 2.5 Connection to Device Under Test ... 45 2.5.1 Connection to Single DUT ... 45 2.5.2 Connection to 1750 Digibridge ... 46 2.5.3 Connection to 7000 Series Precision LCR Meter ... 48 2.5.4 Connection to 1900 Series Precision Impedance Meter ... 49 2.6 Measurement Procedure ... 56 2.6.1 Bias Current source ... 56 2.6.1.1 Programming Example #1: Single Current Test ... 59 2.6.1.2 Programming Example #2: Multi-Point Current Test ... 60 2.6.1.3 Programming Example #3: Multi-Point Current Loop ... 61 2.6.2 DCR (DC Resistance) Measurement ... 62 2.6.3 Error Messages ... 63 Interface – Section 3 3.1 IEEE-488 Interface ... 66 3.1.1 Pin Configuration ... 66 3.1.2 Address Change ... 67 3.1.3 Interface Codes ... 67 3.1.4 Interface Bus & Messages ... 68 3.1.5 Listener Functions ... 69 3.1.5.1 Common Commands ... 69 3.1.5.2 System Commands ... 70 3.2 Handler Interface ... 71 3.3 1320S Bias Current source Slave ... 73 3.4.1 Front Panel Controls and Indicators ... 74 3.4.2 Rear Panel Controls and Connectors ... 75 3.4.3 Slave Interface Pin Configuration ... 76 3.4.4 Slave Connection to 1320 ... 76 Service & Calibration - Section 4 4.1 General ... ... 79 4.2 Instrument Return ... ... 79 4.3 Calibration ... 79 4.3.1 Equipment Required ... 80 4.3.2 1320 Calibration (MASTER) ... 80 4.3.2.1 Sink Board Current Adjustment ... 80 4.3.2.2 DCR Board Voltage Adjustment ... 83 4.3.3 1320S Calibration (SLAVE) ... 84

mehr