Telecommunications Techniques Corporation 550B+ Analyzer
Hersteller:
Modell:
550B+
Datum:
2000
Kategorie:
Gruppe:
Beschreibung:
ISDN BRI Portable Test Set

Information

The TPI 550B+ ISDN BRI Test Set, illustrated below, is a compact, battery operated device used to conduct testing of ISDN circuits at the customer premise, the input and output of the ISDN repeater housing, or at the main distribution frame. The TPI 550B+ is designed both for rugged durability and ease of use, with menu driven screens. Figure 1 — TPI 550B+ ISDN BRI Test Set The TPI 550B+'s operating modes allow it to function as an NT1 (Network Termination), as TE (Terminal Equipment), as both (NT1/TE), as LT (Line Termination), or in a Monitor mode (for monitoring D channel info). It may be connected to either the DSL (Digital Subscriber Loop) U Interface or the S/T Interface. It is compatible with the 2B IQ DSL interface, EBS (P-Phone) Interface, and POTS Line Interface. The TPI 550B+ allows placement of additional loss on the circuit, either at the LINE U Interface or the S/T Interface for margin analysis testing. The TPI 550B+ ISDN BRI Test Set allows selection of loopbacks for each of the B channels, or for the full bandwidth (2B+D). The TPI 550B+ also responds to network controlled loopbacks at the NT1. ISDN testing and measurements made by the TPI 550B+ include: f FEBE (Far End Block Errors) and FEBE Errored Seconds in all ISDN U Interface modes. y Cyclic Redundancy Check (CRC) Errors and CRC Errored Seconds with 2B1Q Interface selected. y S/T FRAME Errors and Errored Seconds, and Bipolar Violations (BPV’s) and Errored Seconds on the S/T Interface in NT1 and TE modes. y Bearer Service selections. - Circuit-Switched Voice, 3.1kHz Audio - Circuit-Switched Data - B- or D-Packet > Intelligent Testing (IT) features. - Auto Bearer Service tests, Local and Distant - Auto SPID/Guess SPID - Video Test (Channel Delay and Dual BERT) - Test Macro (dial test number and run test for each Bearer service) f Dual Call Testing. y Bit Error Testing, with G.821 Results. y B channel Delay. y D channel message analysis. y Cause Messages. y Layer 1, 2, 3 States. y BRIV Support. * Pre-Qualification of Loop. - LT Emulation, generating Layer 1 2B1Q signal - Generation of 40 kHz Test Tone - Intercom mode t Optional U Interface Monitor. >■ Parameter Download. * Optional Service Testing. - EBS (P-Phone) and POTS - IDSL - SDSL - Total Reach ISDN/DDS

mehr

Bedienungsanleitung
Dokumenttyp:
Bedienungsanleitung
Seiten:
278
Größe:
9.27 Mbytes (9721789 Bytes)
Sprache:
english
Revision:
Issue 4
Dokument-ID:
Datum:
2000 09 01
Qualität:
Gescanntes Dokument, alles ist lesbar.
Upload Datum:
2017 01 15
MD5:
7745ee88a3250e2c0ea3a1edec3f18b3
Downloads:
432

Information

Purpose and scope ... xi Assumptions ... xi Getting technical assistance ... xii Using this guide ... x'tii Conventions ... xiv Usage of terms and symbols ... xv Terms and symbols tn manual ... xv Chapter 1—Safety Information ... 1 TPI 550B+ safety considerations ... 2 Other safety information ... 4 General telecommunications safety,, ... ,, ... 5 Chapter 2—Introduction ... ... ... 7 General information ... 8 Physical description ... 14 Controls and indicators ... 15 Display and keypad ... 16 Mode and status LED's ... 18 Interface panel ... 21 Chapter 3—Menus ... 25 Setup ... 26 1/STATUS menu ... 33 STATES submenu ... 34 CAUSE submenu ... 43 RESULT submenu ... 52 2/AUTO menu ... 56 SPID submenu ... 57 BEARER TEST submenu ... 61 IT Macro submenu ... 63 Parameter Download submenu ... 65 VIDEO submenu ... 65 Auto CACH detect submenu ... 66 Auto call control submenu ... 67 3/BERT menu ... 67 •/STORE menu ... 77 FUTILITY menu ... 78 MODES submenu ... 78 CONFIG submenu ... 91 DATA submenu ... 101 Hook On/Off menu ... 111 REDIAL softkey ... 111 SPEED softkey ... 112 SPID soft key ... 112 Chapter 4—Operation ... 115 Power up., ... 116 Setup ... 117 Placing calls ... 124 Voice call ... 124 Data call ... 130 D Channel Packet Call ... 132 B Channel Packet Call ... 135 Pre-qualifying cable pairs ... 137 Testing at the U Interface ... 145 Testing at the S/T interface ... 146 Dual call capability ... 147 Overview ... 147 Additional call offering test ... 147 Details ... 147 BRIV ... 152 NT1 replacement ... 152 Monitor D channel packets (option) ... 154 One person ISDN BRI turn-up ... 159 Equipment ... 159 General Information ... 159 Chapter 5—Options ... 163 P-PHONE (EBS) option ... 164 EBS setup ... 165 EBS operation ... 166 POTS option ... 172 POTS setup ... 172 POTS operation ... 173 U-Mon option ... 174 U-Mon setup ... 175 U-Mon menus ... 178 U-Mon operation ... 186 SDSL option ... 188 SDSL setup ... 188 SDSL menus ... 192 SDSL operation ... 205 Total Reach DDS option ... 206 Total Reach ISDN option ... 208 Chapter 6—Customer Services ... 209 About our services ... 210 Customer service locations ... 210 Instrument services ... 211 Product Enhancement Group ... 212 Test systems field engineering and Installation ... 213 Technical training ... 213 Warranty Information ... 215 Equipment return instructions ... 218 Appendix A—Cables and Accessories ... 219 Cables and accessories ... 220 Optional features ... 220 Appendix B—Quick Reference ... 223 How to make a voice call ... 224 Voice call troubleshooting tips ... 225 How to make a data call ... 226 Data call troubleshooting tips ... 227 How to make a dual B channel call ... 228 Dual call troubleshooting tips ... 229 How to make a D-Pkt call ... 230 D-Pkt troubleshooting tips ... 231 How to make a B-Pkt call ... 233 B-Pkt troubleshooting tips ... 234 One person voice turn-up ... 235 One person circuit-switched data turn-up ... 236 One person D-Pkt turn-up ... 236 One person B-Pkt turn-up ... 237 Testing B channel delay ... 238 Menu Tree.,..* ... 239 Appendix C—Maintenance ... 241 Maintenance ... 242 Firmware card ... 242 Battery recharge ... 244 Battery replacement ... 244 Appendix D—Specifications ... 247 Physical ... 248 Operational ... 249 Measurements ... 250 LED Indicators ... 251 GLOSSARY 253

mehr